This
task
shows
you
how
to
verify
the
installation
after
you
install
the
SAN
Volume
Controller
2145-8F4
or
the
SAN
Volume
Controller
2145-8F2
in
the
rack
and
connect
it
to
the
uninterruptible
power
supply,
the
storage
area
network
(SAN),
and
the
Ethernet.
Note:
If
at
any
point
the
SAN
Volume
Controller
does
not
operate
as
described,
see
“MAP
5000:
Start”
in
the
IBM
System
Storage
SAN
Volume
Controller:
Service
Guide
,
unless
a
different
maintenance
analysis
procedure
(MAP)
is
specified.
Perform
the
following
steps
to
verify
installation:
1.
Press
the
SAN
Volume
Controller
power
switch.
Verify
that
the
green
power
light
is
on.
If
the
light
is
not
on,
see
“MAP
5000:
Start”
in
the
IBM
System
Storage
SAN
Volume
Controller:
Service
Guide
to
repair
the
problem.
Note:
You
do
not
need
to
install
any
software.
The
node
boots
automatically.
Verify
that
the
node
is
booting
without
error.
If
it
boots
without
error,
either
the
Charging
message
or
Cluster:
is
displayed
in
the
first
line
of
the
front-panel
display.
In
most
cases,
the
battery
is
delivered
charged,
so
you
do
not
see
the
Charging
message.
If
the
Charging
message
is
displayed,
you
will
also
see
a
progress
bar
on
the
second
line.
Battery
charging
can
take
up
to
three
hours
to
complete.
In
the
meantime,
if
you
press
any
navigation
buttons,
the
battery
charging
menu
is
replaced,
but
battery
charging
continues.
(You
can
re-enter
the
menu
system
to
view
the
charging
progress,
as
described
in
step
When
the
battery
is
charged
enough,
Cluster:
is
displayed
on
the
first
line
of
the
front-panel
display.
The
second
line
is
left
blank.
2.
Press
and
hold
the
select
button
for
five
seconds.
The
check
light
comes
on
and
a
display
test
is
performed.
When
the
display
test
is
complete,
the
check
light
goes
off
and
a
button
test
is
started.
3.
Press
the
up,
down,
left,
and
right
buttons
to
verify
that
they
are
working.
shows
four
examples
of
what
the
front
panel
should
display
when
you
press
the
buttons.
When
you
have
finished
testing
the
buttons,
press
and
hold
the
select
button
for
five
seconds
in
order
to
exit
the
test.
4.
If
the
Charging
message
is
displayed
on
the
front
panel
display,
press
the
select
button
to
switch
to
the
menu.
The
menu
continues
to
be
displayed
while
you
press
the
buttons
on
the
front
panel.
If
you
do
not
press
any
No button pressed (border only)
Up button pressed
Left and Right button pressed
Select button pressed
Figure
70.
Front
panel
display
when
push
buttons
are
pressed
96
IBM
System
Storage
SAN
Volume
Controller:
Hardware
Installation
Guide
|
|
|
|
|
|
|
Summary of Contents for 2145UPS-1U
