Installing
the
SAN
Volume
Controller
2145-8G4
There
are
several
steps
that
you
must
perform
to
install
the
SAN
Volume
Controller
2145-8G4
node.
Installing
the
SAN
Volume
Controller
2145-8G4
consists
of
the
following
tasks:
1.
Installing
the
support
rails
in
the
rack
cabinet.
2.
Installing
the
SAN
Volume
Controller
2145-8G4.
3.
Connecting
the
SAN
Volume
Controller
2145-8G4
to
the
UPS.
4.
Installing
the
cable
retention
bracket
on
the
SAN
Volume
Controller
2145-8G4.
Installation
guidelines
Before
you
install
the
support
rails,
review
the
following
guidelines:
v
Do
not
install
a
unit
in
a
rack
where
the
internal
rack
ambient
temperatures
exceeds
the
manufacturer’s
recommended
ambient
temperature
for
all
your
rack-mounted
devices.
v
Do
not
install
a
unit
in
a
rack
where
the
air
flow
is
compromised.
Ensure
that
air
flow
is
not
blocked
or
reduced
on
any
side,
front,
or
back
of
a
unit
used
for
air
flow
through
the
unit.
v
Ensure
that
the
equipment
is
connected
properly
to
the
supply
circuit
so
that
the
circuits
do
not
overload
and
compromise
the
supply
wiring
or
overcurrrent
protection.
v
Plan
the
device
installation
starting
at
the
bottom
of
the
rack
cabinet.
v
Install
the
heaviest
device
in
the
bottom
of
the
rack
cabinet.
v
Do
not
install
a
SAN
Volume
Controller
node
directly
above
the
pull-out
monitor
and
keyboard
of
the
master
console.
The
front
panel
of
the
node
protrudes
beyond
the
front
of
the
rack
and
overlaps
part
of
the
monitor,
which
prevents
you
from
being
able
to
open
it.
Installing
the
support
rails
for
the
SAN
Volume
Controller
2145-8G4
You
must
install
the
support
rails
that
hold
the
SAN
Volume
Controller
2145-8G4.
When
you
are
ready
to
install
the
support
rails,
perform
the
following
tasks:
v
Refer
to
the
Hardware
Location
Chart
to
determine
where
the
SAN
Volume
Controller
is
to
be
installed
in
the
rack.
v
Refer
to
the
Electronic
Industries
Alliance
(EIA)
markings
on
the
rack
and
decide
where
you
are
going
to
install
the
support
rails.
Perform
the
following
steps
to
install
the
support
rails
(shown
in
for
the
SAN
Volume
Controller
2145-8G4:
1.
Make
sure
you
have
all
the
items
that
you
need
for
installing
the
support
rails.
Chapter
6.
Installing
the
SAN
Volume
Controller
2145-8G4
hardware
49
|
|
|
|
|
Summary of Contents for 2145UPS-1U
