expect "16\r" or "15\r" or "14\r" or "12\r" or "10\r" or "5\r" or "1\r" busy "7\r"
timeout 60
done
retry:
send "A/"
# Repeat the previous command.
# Expect a connection response.
expect "16\r" or "15\r" or "14\r" or "12\r" or "10\r" or "5\r" or "1\r" busy "7\r"
timeout 60
done
disconnect:
delay 2
# Separate from previous data.
send "+++"
# Assure command mode.
delay 2
# Allow mode switching delay.
send "ATH0T\r"
# Set modem switch-hook down
# (i.e., hang up).
ignore "0\r" or "OK\r" timeout 2
# Ignore modem response.
send "ATE0Q1\r"
# Initialize modem: Echo OFF,
# Disable responses.
ignore "0\r" timeout 1
done
condin:
send "AT&F0Q0T\r"
# Reset modem. Select profile 0
ignore "0\r" or "OK\r\n" timeout 2 # Ignore modem response.
send "ATE0T\r"
# Initialize modem: Echo OFF,
expect "0\r" or "OK\r\n" timeout 2 # Enable responses (Numeric),
send "ATQ0V0X0T\r"
# Limit response codes.
expect "0\r" timeout 2
# Confirm commands successful.
send "ATS0=2\r"
# Set AutoAnswer ON
expect "0\r" timeout 2
# Confirm command successful.
send "AT&C1&D2&R1\r"
# Detect carrier and DTR,
# Ignore RTS.
expect "0\r" timeout 2
# Confirm command successful.
done
waitcall: ignore "2\r" timeout 1
# Ignore first ring.
expect "2\r" timeout 10
# Pick up second ring
# or timeout.
# Expect a connection response.
expect "16\r" or "15\r" or "14\r" or "12\r" or "10\r" or "5\r" or "1\r"
timeout 60
done
page:
send "ATDT%N,,,,%R;\r"
# %N = pager call center number
# Add enough commas to wait for
# time to enter paging number.
# %R = paging number
# Confirm successful command.
expect "0\r" timeout 60
delay 2
# Wait before hanging up.
send "ATH0T\r"
# Hang up.
expect "0\r" timeout 2
# Confirm successful command.
done
ripo:
send "AT&F0Q0T\r"
# Reset modem. Select profile 0
ignore "0\r" or "OK\r\n" timeout 2 # Ignore modem response.
send "ATE0T\r"
# Initialize modem: Echo OFF,
expect "0\r" or "OK\r\n" timeout 2 # Enable responses (Numeric),
send "ATQ0V0X0T\r"
# Limit response codes.
expect "0\r" timeout 2
# Confirm commands successful.
send "ATS0=0\r"
# Set AutoAnswer OFF
expect "0\r" timeout 2
# Confirm command successful.
send "AT&C1&D2&R1\r"
# Detect carrier and DTR,
# Ignore RTS.
expect "0\r" timeout 2
# Confirm command successful.
Appendix D. Modem Configurations
333
Summary of Contents for 265
