IBM 4232 Model 302 Manual Download | Manualshive

Page: 239 / 274

background image

Cut Sheet Forms — F3
Dimensions

Forms

Maximum

Minimum

Width

381 mm (15 in.)

76.2 mm (3 in.)

Length

355.6 mm (14 in.)

177.8 mm (7 in.)

Thickness

The thickness of all forms should be a minimum of 0.08 mm (0.003
in.) and a maximum of 0.25 mm (0.010 in.).

Acceptable print quality will be provided when using single-part
forms. If you use forms having more than one part, you should test
them for forms handling, print registration, and print quality.

Weight

Minimum weight for single-part forms is 56 g/m

ò

(15 lb). Maximum

weight for single-part forms is 150 g/m

ò

(40 lb). The best range is

75 to 90 g/m

ò

(20 to 24 lb). Paper weights outside the functional

range should be tested by the user.

Performance Considerations

When using the F3 device, you can use a width of up to 381 mm (15
in.). However, for optimum feeding and print registration, a
maximum width of 330 mm (13 in.) is recommended. For optimum
performance, printing should be restricted to 12.7 mm (0.5 in.) from
all edges of the form.

Forms are available from IBM or any forms supplier.

Appendix C. Forms Information

C-3

«
...
237
238
239
240
241
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

Brand: Datecs Pages: 73

Brand: Datamax Pages: 12

E-Class Mark II

Brand: Datamax Pages: 40

Brand: Datamax Pages: 46

Nimbie Sidekick NK50Y

Brand: Acronova Technology Pages: 2

Brand: Epson Stylus Pages: 4

Brand: Ascend Pages: 6

Brand: Oce Pages: 76

Brand: Skynet Pages: 18

Brand: Sawgrass Pages: 2

Brand: Lexmark Pages: 121

SLK-T21EB Series

Brand: SEWOO Pages: 12

Brand: Sewhacnm Pages: 6

Brand: SEWOO Pages: 13

Brand: Digital Equipment Pages: 120

Brand: Digital Equipment Pages: 142

Brand: Digital Equipment Pages: 208

Hello BEE Prusa

Brand: Beeverycreative Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands