IBM 4232 Model 302 Manual Download | Manualshive

Page: 242 / 274

background image

Additional Forms Restrictions

For best results when printing, the following forms restrictions apply:

Fastening recommendations:

– Form plies must not be fastened with any staples and must

be fastened securely enough to prevent partial forms
separation.

– For the F3 forms device, multiple-part forms must be glued

only at the top edge and fastened securely enough to
prevent forms separation.

– For the F4 forms device, only top-glued or snap-out

multiple-part forms should be used.

– If crimp fasteners are used, you should consider the

following:

- Crimps should not project significantly above the surface

of the first form to avoid ribbon interference.

- Crimps should not add significantly to the total forms

thickness.

- The protruding tail of the crimp should be opposite the

direction of forms motion so that the forms motion tends
to compress and tighten the crimp. The crimp should
also be away from the surface of the forms where
printing is occurring to avoid ribbon interference.

- Excessively hard or stiff crimps can interfere with proper

ribbon and forms processing operation.

Forms stacking:

– For best stacking efficiency, the distance between folds

should be 152.4 to 317.5 mm (6 to 12.5 in.).

Feed holes should be free of chads and crimps to avoid false
form jam errors.

Forms should be strong enough to prevent tearing of feed holes.

Label forms should be tested for satisfactory forms handling,
print registration, and print quality.

Do not use forms that have started to come apart.

C-6

User’s Guide Model 302

«
...
240
241
242
243
244
...
»

Summary of Contents for 4232 Model 302



















































































































































































































































































Reviews:

No comments

Related manuals for 4232 Model 302

Brand: Oki Pages: 16

Brand: Panasonic Pages: 83

Brand: Panasonic Pages: 155

Brand: Panasonic Pages: 160

Brand: BadgePass Pages: 2

VariQuest Perfecta 2400STP

Brand: Varitronics Pages: 227

Pixma TS7700i Series

Brand: Canon Pages: 554

Brand: Oki Pages: 98

Brand: OKIDATA Pages: 182

Brand: A&D Pages: 16

Brand: Alunar Pages: 6

Brand: FOREVER Pages: 2

Brand: Oki Pages: 336

Brand: SPRT Pages: 17

Brand: Bresser Pages: 104

Brand: Oki Pages: 110

Brand: SprintRay Pages: 6

Brand: d.gen Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands