IBM 7383 Installation And Service Manual Download | Manualshive

Page: 12 / 488

background image

Guidelines for servicing electrical equipment

Observe these guidelines when you service electrical equipment.

v

Check the area for electrical hazards such as moist floors, nongrounded power
extension cords, and missing safety grounds.

v

Use only approved tools and test equipment. Some hand tools have handles that
are covered with a soft material that does not provide insulation from live
electrical current.

v

Regularly inspect and maintain your electrical hand tools for safe operational
condition. Do not use worn or broken tools or testers.

v

Do not touch the reflective surface of a dental mirror to a live electrical circuit.
The surface is conductive and can cause personal injury or equipment damage if
it touches a live electrical circuit.

v

Some rubber floor mats contain small conductive fibers to decrease electrostatic
discharge. Do not use this type of mat to protect yourself from electrical shock.

v

Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.

v

Locate the emergency power-off (EPO) switch, disconnecting switch, or electrical
outlet so that you can turn off the power quickly in the event of an electrical
accident.

v

Disconnect all power before you perform a mechanical inspection, work near
power supplies, or remove or install main units.

v

Before you work on the equipment, disconnect the power cord. If you cannot
disconnect the power cord, have the customer power-off the wall box that
supplies power to the equipment and lock the wall box in the off position.

v

Never assume that power has been disconnected from a circuit. Check it to
make sure that it has been disconnected.

v

If you have to work on equipment that has exposed electrical circuits, observe
the following precautions:
– Make sure that another person who is familiar with the power-off controls is

near you and is available to turn off the power if necessary.

– When you work with powered-on electrical equipment, use only one hand.

Keep the other hand in your pocket or behind your back to avoid creating a
complete circuit that could cause an electrical shock.

– When you use a tester, set the controls correctly and use the approved probe

leads and accessories for that tester.

– Stand on a suitable rubber mat to insulate you from grounds such as metal

floor strips and equipment frames.

v

Use extreme care when you measure high voltages.

v

To ensure proper grounding of components such as power supplies, pumps,
blowers, fans, and motor generators, do not service these components outside of
their normal operating locations.

v

If an electrical accident occurs, use caution, turn off the power, and send another
person to get medical aid.

x

System x3500 M4 Type 7383: Installation and Service Guide

«
...
10
11
12
13
14
...
»

Summary of Contents for 7383









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7383

Brand: SilverStone Pages: 44

Data Express Ultra320 DE100

Brand: StorCase Technology Pages: 31

Brand: Hamlet Pages: 4

PLUSView1000 AMG User’s

Brand: Antec Pages: 3

Brand: Chenbro Pages: 22

Brand: StarTech.com Pages: 13

Brand: Argus Pages: 24

Brand: Argus Pages: 24

Brand: Thermaltake Pages: 12

MetalHead MH-412SL

Brand: Fender Pages: 1

Brand: Fender Pages: 8

Brand: V7 Pages: 11

Brand: Pulsar Pages: 4

SYNO Dome Closure series

Brand: R&M Pages: 17

Brand: Rockford Fosgate Pages: 11

Brand: Macpower & Tytech Pages: 13

Brand: Vantec Pages: 18

Brand: molex Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands