Table 37. UEFI/POST diagnostic codes (continued)
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.
v
If an action step is preceded by “(Trained technician only)”, that step must be performed only by a trained
technician.
v
Go to the IBM support website at http://www.ibm.com/supportportal to check for technical information, hints,
tips, and new device drivers or to submit a request for information.
Diagnostic
code
Message
Description
Action
I.2018002
[I.2018002] The
device found at Bus
% Device %
Function % could
not be configured
due to resource
constraints. The
Vendor ID for the
device is % and the
Device ID is %.
OUT_OF_RESOURCES
(PCI Option
ROM).
1.
If this PCIe device and/or any attached cables were
recently installed, moved, serviced or upgraded, reseat
adapter and any attached cables.
2.
Update the PCI adapter firmware.
3.
Move card to a different slot. If the slot is not available or
error re-occurs, replace the adapter (see Removing an
adapter and Installing an adapter).
4.
(Trained technician only) If adapter was moved to a
different slot and error did not re-occur, verify that this is
not a system limitation and then replace the system board.
Also, if this is not the initial installation and the error
persists after adapter replacement, replace system board
(see Removing the system board and Installing the system
board).
5.
Run the Setup utility (see Using the Setup utility). Select
Startup Options
from the menu and modify the boot
sequence to change the load order of the optional-device
ROM code.
6.
Informational message that some devices might not be
initialized.
7.
See retain tip H197144 for more information.
I.2018003
[I.2018003] A bad
option ROM
checksum was
detected for the
device found at Bus
% Device %
Function %. The
Vendor ID for the
device is % and the
Device ID is %.
ROM
CHECKSUM
ERROR.
1.
Check the PCI LEDs.
2.
Reseat all affected adapters and the PCI-X interposer card.
3.
Move the affected adapter to a different slot.
4.
Update the PCI adapter firmware.
5.
Replace the affected adapters and (see Removing an
adapter and Installing an adapter).
S.3020007
[S.3020007] A
firmware fault has
been detected in the
UEFI image.
Internal UEFI
Firmware Fault
Detected,
System halted.
1.
Check the IBM support website for an applicable retain tip
or firmware update that applies to this error.
2.
Recover the server firmware (see Recovering the server
firmware).
3.
(Trained technician only) replace the system board (see
Removing the system board and Installing the system
board).
354
System x3500 M4 Type 7383: Installation and Service Guide
Summary of Contents for 7383
