Table 37. UEFI/POST diagnostic codes (continued)
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.
v
If an action step is preceded by “(Trained technician only)”, that step must be performed only by a trained
technician.
v
Go to the IBM support website at http://www.ibm.com/supportportal to check for technical information, hints,
tips, and new device drivers or to submit a request for information.
Diagnostic
code
Message
Description
Action
S.3028002
[S.3028002] Boot
permission timeout
detected.
Boot
Permission
Negotiation
Timeout.
1.
Check the IMM2 error messages (see Integrated
management module II (IMM2) error messages) for
communication errors and follow the actions.
2.
Restart the server.
3.
If the problem remains, contact your IBM service
representative for support.
S.3030007
[S.3030007] A
firmware fault has
been detected in the
UEFI image.
Internal UEFI
Firmware Fault
Detected,
System halted.
1.
Check the IBM support website for an applicable retain tip
or firmware update that applies to this error.
2.
Recover the server firmware (see Recovering the server
firmware).
3.
(Trained technician only) replace the system board (see
Removing the system board and Installing the system
board).
S.3040007
[S.3040007] A
firmware fault has
been detected in the
UEFI image.
Internal UEFI
Firmware Fault
Detected,
System halted.
1.
Check the IBM support website for an applicable retain tip
or firmware update that applies to this error.
2.
Recover the server firmware (see Recovering the server
firmware).
3.
(Trained technician only) replace the system board (see
Removing the system board and Installing the system
board).
I.3048005
[I.3048005] UEFI has
booted from the
backup flash bank.
Booting Backup
UEFI Image.
Information only. Turn the switch 1 of the SW4 on to allow the
server to boot from the backup UEFI (see System-board
switches and jumpers).
W.3048006
[W.3048006] UEFI
has booted from the
backup flash bank
due to an
Automatic Boot
Recovery (ABR)
event.
Automated
Boot Recovery,
Booting Backup
UEFI Image.
1.
Check the IBM support website for an applicable retain tip
or firmware update that applies to this error.
2.
Recover the server firmware (see Recovering the server
firmware).
3.
(Trained technician only) replace the system board (see
Removing the system board and Installing the system
board).
S.3050007
[S.3050007] A
firmware fault has
been detected in the
UEFI image.
Internal UEFI
Firmware Fault
Detected,
System halted.
1.
Check the IBM support website for an applicable retain tip
or firmware update that applies to this error.
2.
Recover the server firmware (see Recovering the server
firmware).
Appendix A. UEFI/POST error codes
355
Summary of Contents for 7383
