Ethernet controller messages
The integrated Ethernet controller might display messages from the following
device drivers:
v
Novell
™
NetWare
™
or IntraNetWare Server ODI
v
NDIS Adapter for level 4.0 (Windows NT)
Novell NetWare or IntraNetWare server ODI driver teaming
messages
This section provides explanations of the error messages for the Novell NetWare or
IntraNetWare server ODI driver, and suggested actions to resolve each problem.
Table 4. NetWare driver messages for the Ethernet controller
Message
Description
Couldn’t allocate resources
Explanation:
An unknown error has occurred when trying
to allocate needed resources for the AFT Module.
Action:
v
Check the server configuration. If the problem persists,
contact your network supplier.
v
Verify that the Ethernet controller is enabled. If the
Ethernet controller is enabled, run the diagnostic
programs.
AFT group for primary
adapter in slot
nnn
already
exists.
Explanation:
An attempt was made to rebind an adapter
already in an AFT group.
Action:
Check the AFT slot
numbers for existing AFT teams. If the problem persists,
contact your network supplier.
Error locating DCT addresses
in internal table. Make sure
that you have loaded LAN
drivers after loading
AFT.NLM.
Explanation:
The bind command was entered prior to
loading the device driver. The device driver must be loaded
after loading AFT.NLM but before any bind command can
be issued.
Action:
Load the driver for the supported
adapter and try loading the AFT module again. If the
problem persists, contact your network supplier.
Insufficient number of
arguments specified.
Explanation:
The appropriate or expected number of
parameters was not entered in a command.
Action:
Check
the parameters required for the given command. If the
problem persists, contact your network supplier.
Duplicate slot numbers
detected.
Explanation:
An attempt has been made to bind the same
slot number more than once.
Action:
Check the slot
numbers entered during the bind. Adapter slot numbers
must be valid and unique. If the problem persists, contact
your network supplier.
’
Xxx
’ is not supported for
AFT team.
Explanation:
A bind command has been issued for adapters
not supported by AFT.NLM.
Action:
Make sure that you
attempt to bind only adapters supported by AFT.NLM.
Primary and Secondary
adapters do not match. AFT
group is not created.
Explanation:
A bind command was entered for an adapter
team that is a combination of server and client adapters. An
AFT team must be a grouping of the same classification of
adapter.
Action:
Verify that all the adapters bound in a
team are of the same classification.
Requested number of
Secondary cards are not
found.
Explanation:
The number of adapters specified in the bind
command could not be located.
Action:
Verify the numbers
and slot locations of the adapters to be bound. If the
problem persists, contact your network supplier.
Diagnostics
23
Summary of Contents for 8645 - Eserver xSeries 220
