background image

 Chapter 4. Installation 

139

4.3.3  Installation

In this section we discuss installation.

The installation here assumes that you will be installing Windows Server 2003 on 
a brand new pair of disks, disks that have no data on them, or disks that have 
data that can be destroyed.

If you are installing on disks that have data that you want to keep, you will see 
additional messages. Please read this information carefully and refer to earlier 
sections of this chapter for additional help.

Starting the installation CD automatically

To start the installation automatically, proceed as follows:

1. Insert the installation CD in the drive.

2. From the EFI Firmware Boot Manager menu, select the CD-ROM entry in the 

list (as shown in Figure 4-40 on page 140) and press Enter.

Note: Earlier problems that affected the installation of Windows Server 
2003 on the x455 with an RXE-100 attached have now been resolved. It is 
no longer necessary to disconnect the RXE-100 before the installation.

Tip: Official installation instructions are typically available on the Web. 
However, at the time of writing none were published for the x455. Once they 
are available, they will be accessible at: 

http://www.pc.ibm.com/support

 

Select the x455 (8855) and select OS Installation document type.

Tip: If the disk you install to is still an MBR disk, the installation procedure will 
prompt you to convert the disk to a GPT structure.

Summary of Contents for 88553RX









































































































































































































































Reviews: