11. If you do not plan to install another adapter into the vacated slot, seal the
expansion slot using an expansion-slot cover. If you are installing another adapter,
go to “Adding or Replacing a Non-Hot-Pluggable PCI Adapter”.
12. If you have other options to install, refer to “Options and Task List” on page 51. If
you do not have other options to install, continue on to the next step.
13. Replace the service access cover as described in “Service Access Cover
Replacement (Model 6C4)” on page 55 or “Service Access Cover Replacement
(Model 6E4)” on page 58.
14. On a Model 6C4, push the system drawer back into the operating position as
described in “Returning the Model 6C4 to the Operating Position” on page 54.
15. Connect the adapter cables.
16. On a Model 6C4, route the cables through the cable management arm.
17. Power on the system as described in “Starting the System” on page 52.
18. On a Model 6C4, close the rack doors.
On a Model 6E4, close the bezel door.
Adding or Replacing a Non-Hot-Pluggable PCI Adapter
To add or install an adapter, do the following:
1. On a Model 6C4, open the front and rear rack doors and put the system into the
service position as described in “Placing the Model 6C4 into the Service Position”
On a Model 6E4, open the bezel door.
2. Shut down the system as described in “Stopping the System” on page 52.
3. Remove the service access cover as described in “Service Access Cover Removal
(Model 6C4)” on page 55 or “Service Access Cover Removal (Model 6E4)” on
page 57.
4. Refer to the
PCI Adapter Placement Reference for information regarding slot
restrictions for adapters that can be used in this system.
5. If necessary, remove the adapter expansion slot shield.
6. Before handling any card, board, or memory DIMM, touch any metal surface of the
chassis with one hand to minimize static electric discharge. Refer to “Handling
Static-Sensitive Devices” on page 50.
7. If necessary, remove the adapter from the antistatic package.
Attention: Avoid touching the components and gold-edge connectors on the
adapter.
8. Place the adapter, component-side up, on a flat, static-protective surface.
9. Set any jumpers or switches as instructed by the adapter manufacturer.
78
Eserver
pSeries 630 Model 6C4 and Model 6E4 Installation Guide
Summary of Contents for @Server pSeries 630 6C4
