Table
15.
I/O
DIMM
boot
errors
(continued)
E2002
Incompatible
DIMM
type
(not
registered
type).
The
DIMM
is
not
a
registered
DIMM.
Replace
the
DIMM
with
a
DIMM
of
type
″
registered
″
.
E2011
Incompatible
DIMM
type
(maximum
DIMM
frequency
too
slow).
The
maximum
I/O-frequency
of
the
DIMM
is
slower
than
memory
controller’s
frequency.
Replace
the
DIMM
with
a
DIMM
allowing
an
I/O-frequency
of
at
least
333MHz.
E2012
Incompatible
DIMM
type
(CAS
Latency).
The
DIMM
does
not
provide
a
CAS
Latency
setting
for
an
I/O-frequency
of
333
MHz
or
the
configuration
data
is
inconsistent.
Replace
the
DIMM
with
a
DIMM
with
correct
configuration
data.
E2013
Incompatible
DIMM
type
(Burst
Length).
The
DIMM
does
not
support
a
Burst
Length
of
4.
Replace
the
DIMM
with
a
DIMM
supporting
a
Burst
Length
of
4.
E2014
Incompatible
DIMM
type
(wrong
bank
count).
The
DIMM
has
a
bank
count
different
from
4
and
8.
Replace
the
DIMM
with
a
DIMM
with
a
bank
count
of
4
or
8.
E2021
Incompatible
DIMM
type
(DIMM
data
width).
The
DIMM’s
the
data
width
is
different
from
36
and
72.
Replace
the
DIMM
with
a
DIMM
with
a
data
width
of
36
or
72.
E2022
Incompatible
DIMM
type
(SDRAM
data
width).
The
DIMM’s
data-lanes
are
organized
other
than
“by
8”.
Replace
the
DIMM
with
a
DIMM
with
an
SDRAM
data
width
of
8
lanes.
E2031
Data
error.
The
DIMM
is
defective.
Replace
the
DIMM
with
a
new
one.
E2032
Address
line
error.
The
DIMM
is
defective.
Replace
the
DIMM
with
a
new
one.
The
following
table
shows
the
warning
messages
that
may
appear:
Table
16.
I/O
DIMM
warning
messages
Code
Message
Description
Action
W2081
Unsupported
DIMM
type
(not
512
MB).
The
DIMM
has
a
size
different
from
512MB.
Replace
the
DIMM
with
a
DIMM
of
size
512
MB
to
avoid
compatibility
problems.
W2082
Unsupported
DIMM
type
(CAS
Latency
z
instead
of
5).
The
DIMM
is
operated
with
CAS
Latency
z,
but
only
a
CAS
Latency
of
5
is
supported.
Replace
the
DIMM
with
a
DIMM
with
a
CAS
Latency
of
5
for
an
I/O
frequency
of
333
MHz
to
avoid
compatibility
problems.
W2083
Unsupported
DIMM
type
(contains
more
data
than
program
buffer).
The
SPD
of
the
DIMM
contains
more
data
elements
than
needed.
Replace
the
DIMM
with
an
SPD
of
128
bytes
to
avoid
compatibility
problems.
The
following
table
shows
informational
messages.
Table
17.
I/O
DIMM
informational
messages
Code
Message
Description
Action
No
DIMM.
The
socket
is
not
populated.
Insert
a
DIMM
into
the
empty
socket
to
make
full
use
of
the
I/O-buffer
capability.
In
addition
to
appearing
on
the
console,
messages
are
also
written
to
the
Advanced
Management
Module
log.
The
table
below
lists
the
messages.
Chapter
5.
Diagnostics
and
troubleshooting
87
Summary of Contents for BladeCenter QS21 Type 0792
