where
d
is
any
available
drive
letter.
You
now
can
access
the
EFI
system
partition
as
you
would
any
other
system
drive.
4.
Create
a
directory
on
the
EFI-system-partition
drive
(
d
:)
to
store
the
firmware
update
files.
5.
Go
to
the
IBM
support
site
at
http://www.ibm.com/pc/support/;
then,
download
the
update
package
for
the
xSeries
455
server
to
the
directory
that
you
created
in
step
6.
Extract
the
xSeries
455
update
package
into
the
directory
that
you
created
in
step
Notes:
a.
When
you
extract
the
files,
be
sure
to
maintain
the
folder
structure.
b.
Detailed
instructions
for
updating
the
firmware
are
provided
in
the
readme
file
in
each
code-specific
folder.
7.
Shut
down
the
operating
system;
then,
restart
the
server
to
the
EFI
shell.
8.
Change
to
the
file
system
(fsx:)
that
corresponds
to
the
EFI
system
partition;
then,
change
directories
to
the
update
directory.
9.
Follow
the
instructions
provided
in
the
package
readme.txt
files
to
install
the
firmware
updates.
Creating
an
update
CD
when
using
SLES8
If
you
are
using
the
SLES8
operating
system,
use
the
instructions
in
this
section
to
create
a
firmware
update
CD
from
the
ISO
image;
then,
see
the
readme.txt
file
in
the
root
directory
of
the
firmware
update
CD,
under
EFI.
Note:
Detailed
instructions
for
using
the
CD
to
update
the
firmware
are
provided
with
the
code
in
each
code-specific
subdirectory.
The
Linux
IDE
ATAPI
CD-ROM
device
driver
uses
SCSI
emulation
for
CD
read
and
write
operations.
If
a
boot
option
to
enable
IDE-SCSI
emulation
was
not
included
during
the
installation
process,
you
must
add
the
boot
option
to
the
elilo.conf
file.
In
most
cases,
the
IDE
DVD/CD-RW
drive
in
the
xSeries
455
server
is
the
first
IDE
device.
To
enable
the
IDE-SCSI
emulation,
add
the
following
boot
option
to
the
stanza
for
the
kernel
you
are
booting:
append="hda=ide-scsi"
For
example,
the
kernel
might
have
the
following
stanza:
image=/vmlinuz
label=linux
root=802
initrd=/initrd
append="console=ttyS0,115200n8,
console=tty0"
After
it
is
modified,
the
stanza
appears
as
follows:
image=/vmlinuz
label=linux
root=802
initrd=/initrd
append="console=ttyS0,115200n8,
console=tty0
hda=ide-scsi"
Restart
the
server.
Complete
the
following
steps
to
create
the
CD:
Chapter
2.
Hints
and
tips
9
Summary of Contents for Eserver xSeries 455
