3.
Disconnect
the
cables
and
power
cords
from
the
rear
of
the
server.
Attention:
When
you
handle
static-sensitive
devices,
take
precautions
to
avoid
damage
from
static
electricity.
See
the
documentation
that
comes
with
the
server
for
details
about
handling
these
devices.
4.
Remove
fans
3
and
4.
5.
Locate
the
SAL/EFI
code-page
jumper
(J28)
on
the
I/O
board.
1
2
3
Jumper (J28)
6.
If
there
is
a
jumper
on
J28,
move
the
jumper
from
pins
1
and
2
to
pins
2
and
3
to
enable
the
SAL/EFI
backup
code
page.
If
there
is
no
jumper,
add
one
to
J28
pins
2
and
3.
7.
Replace
fans
3
and
4.
8.
Reconnect
the
cables
and
power
cords
to
the
rear
of
the
server.
9.
Restart
the
server
and
follow
the
instructions
on
the
screen.
Within
2
minutes,
the
drive
activity
LED
on
the
DVD/CD-RW
drive
flashes
several
times,
indicating
that
the
recovery
flash
image
is
being
read.
If
the
LED
does
not
flash,
repeat
this
process
using
a
different
CD
containing
the
recovery
flash
image.
If
the
LED
still
does
not
flash,
you
might
need
to
have
the
I/O
board
replaced
to
correct
the
problem.
Call
for
service.
10.
When
the
drive
activity
LED
stops
flashing,
wait
at
least
5
minutes
for
the
flash
update
to
be
completed.
11.
Remove
the
Resource
CD
from
the
drive.
12.
Repeat
steps
through
Then,
continue
with
step
13.
Move
the
jumper
on
J28
to
pins
1
and
2
to
return
to
the
normal
startup
mode.
14.
Replace
fans
3
and
4;
then,
close
the
covers.
15.
Reconnect
the
cables
and
power
cords
to
the
rear
of
the
server.
16.
Restart
the
server.
Note:
You
also
might
have
to
update
the
SAL/EFI
to
the
current
level.
See
for
more
information.
Remote
update
of
SAL/EFI
code
using
the
service
processor
might
fail
Description:
While
the
SAL/EFI
code
is
being
updated
remotely
using
the
service
processor,
the
update
might
fail
and
the
following
message
might
appear
in
the
error
log:
Flash
of
BIOS
(I32)
via
LAN
failed
for
USERID
...
Failed
due
to
incorrect
checksum.
Solution:
In
the
unlikely
event
that
this
problem
occurs,
retry
the
remote
update.
Chapter
2.
Hints
and
tips
11
Summary of Contents for Eserver xSeries 455
