IBM Flex System x440 Compute Node Installation And Service Manual Download

Page: 537 / 584

Installing an I/O expansion adapter

Use this information to install an I/O expansion adapter.

Before you begin

Before you install an I/O expansion adapter, complete the following steps:

Read “Safety” on page v and “Installation guidelines” on page 487.

If the compute node is installed in an IBM Flex System chassis, remove it (see
“Removing a compute node from a chassis” on page 489 for instructions).

Carefully lay the compute node on a flat, static-protective surface, orienting the
compute node with the bezel pointing toward you.

About this task

This component can be installed as an optional device or as a CRU. The
installation procedure is the same for the optional device and the CRU.

Procedure

To install an I/O expansion adapter, complete the following steps.

Expansion
cover

Adapter

Remove the cover (see “Removing the compute node cover” on page 498).

Locate the I/O expansion connectors (see “System-board connectors” on page
16).

Remove the expansion cover

▌1▐

from the connector, if one is present.

Touch the static-protective package that contains the adapter to any

unpainted

metal surface on the IBM Flex System chassis or any

unpainted

metal surface on

any other grounded rack component; then, remove the adapter from the
package.

Open the retention clips if they are closed.

Orient the connector on the expansion adapter with the I/O expansion
connector and alignment pins on the system board

▌2▐

; then, press the adapter

into the I/O expansion connector.

Firmly press on the indicated locations to seat the expansion adapter in the
connector and over the alignment pins.

Close the retention clips

▌3▐

What to do next

After you install the I/O expansion adapter, complete the following steps:

Chapter 7. Installing, removing, and replacing compute node components

525

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands

IBM Flex System x440 Compute Node, Installation And Service Manual

Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands