manualshive.com logo in svg

IBM Flex System x440 Compute Node, Installation And Service Manual

The IBM Flex System x440 Compute Node offers exceptional performance and scalability for demanding workloads. To ensure a seamless setup and maintenance process, an installation and service manual is available for free download from our website. Maximize the potential of this powerful product with our comprehensive user manual.

Share
Download
background image

a.

Use a screwdriver to loosen the screw on one side of the heat sink to break
the seal with the microprocessor.

b.

Use a screwdriver to loosen the screws on the heat sink, rotating each screw
two full turns until each screw is loose.

c.

Gently pull the heat sink from the microprocessor.

Attention:

Do not use any tools or sharp objects to lift the release levers on

the microprocessor socket. Doing so might result in permanent damage to the
system board.

4.

Open the microprocessor socket release levers and retainer.

Microprocessor
retainer

Release
lever

Release
lever

a.

Identify which release lever is labeled as the first release lever to open, and
open it.

b.

Open the second release lever on the microprocessor socket.

c.

Open the microprocessor retainer.

Attention:

Do not touch the connectors on the microprocessor and the

microprocessor socket.

5.

Remove the microprocessor from the socket.

Note:

If you are replacing a microprocessor, use the empty installation tool that

comes with the CRU kit to remove the microprocessor.

a.

Twist the handle on the microprocessor tool counterclockwise so that it is in
the open position.

Installation tool

Handle

b.

Align the installation tool with the screws on the microprocessor socket, and
lower the tool on the microprocessor. The installation tool rests flush on the
socket only if it is aligned correctly.

Chapter 7. Installing, removing, and replacing compute node components

541

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x440 Compute Node

G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Brand: G-Technology Pages: 35
LTS LTAH103C Hardware Integration Manual preview
LTAH103C
Brand: LTS Pages: 5
hager TJA670 domovea Basic Manual preview
TJA670 domovea Basic
Brand: hager Pages: 36
ICP DAS USA UA-5231M Quick Start preview
UA-5231M
Brand: ICP DAS USA Pages: 4
Intergraph InterServe 600 Series System Reference Manual preview
InterServe 600 Series
Brand: Intergraph Pages: 104
Telvue HyperCaster User Manual preview
HyperCaster
Brand: Telvue Pages: 153
Obvius, LLC AcquiLite A7810-0 Installation And Operation Manual preview
AcquiLite A7810-0
Brand: Obvius, LLC Pages: 29
IBM x3350 - System - 4192 User Manual preview
x3350 - System - 4192
Brand: IBM Pages: 98
IBM x3500 - System - 7977 Installation Manual preview
x3500 - System - 7977
Brand: IBM Pages: 124
IBM System x3250 Installation And User Manual preview
System x3250
Brand: IBM Pages: 106
IBM x3200 - System M3 - 7328 Installation Manual preview
x3200 - System M3 - 7328
Brand: IBM Pages: 100
IBM System x3400 Type 7975 Installation Manual preview
System x3400 Type 7975
Brand: IBM Pages: 124
IBM System x3300 M4 Installation And Service Manual preview
System x3300 M4
Brand: IBM Pages: 470
IBM System x iDataPlex dx360 Manual preview
System x iDataPlex dx360
Brand: IBM Pages: 26
HP ProLiant DL100 G2 DPSS Administration Manual preview
ProLiant DL100 G2 DPSS
Brand: HP Pages: 155
HP NetStorage 6000 User Manual preview
NetStorage 6000
Brand: HP Pages: 192
HP ProLiant DL100 G2 DPSS Installation Manual preview
ProLiant DL100 G2 DPSS
Brand: HP Pages: 44
Mitsubishi Electric MES3-255C-DM-EN User Manual preview
MES3-255C-DM-EN
Brand: Mitsubishi Electric Pages: 48

Brands by name

Popular brands

Load more brands