IBM Flex System x440 Compute Node Installation And Service Manual Download

Page: 510 / 584

Attention:

Touching the CMOS battery on a metal surface, such as the side of the

compute node, when you replace the CMOS battery can cause it to fail.

Procedure

To install a CMOS battery, complete the following steps:

Remove the cover (see “Removing the compute node cover”).

Follow any special handling and installation instructions that come with the
CMOS battery.

Locate the CMOS battery socket on the system board (see “System-board
connectors” on page 16).

Orient the CMOS battery so that the positive (+) side faces in toward the center
of the compute node.

Pivot the CMOS battery so that you can insert it into the bottom of the socket.

As you slide the CMOS battery into place, press the top of the CMOS battery
into the socket.

If you removed a cover from the battery, replace the cover.

What to do next

After you install the CMOS battery, complete the following steps:

Install the cover onto the compute node (see “Installing the compute node
cover” on page 500 for instructions).

Install the compute node into the chassis (see “Installing a compute node in a
chassis” on page 490 for instructions).

Turn on the compute node, start the Setup utility, and reset the configuration
(see “Using the Setup utility” on page 26 for instructions).

Removing the compute node cover

Use this information to remove the cover from a compute node.

Before you begin

Before you remove the compute node cover, complete the following steps:

Read “Safety” on page v and “Installation guidelines” on page 487.

If the compute node is installed in a IBM Flex System chassis, remove it (see
“Removing a compute node from a chassis” on page 489 for instructions).

Carefully lay the compute node on a flat, static-protective surface, orienting the
compute node with the bezel pointing toward you.

Statement 12

498

IBM Flex System x440 Compute Node Types 7917 and 2584: Installation and Service Guide

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands

IBM Flex System x440 Compute Node, Installation And Service Manual

Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands