Sample File modem_f1.cfg
#
# COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F1
#
# FUNCTIONS: Modem configuration file for many recent Hayes\ compatible modems.
#
This example uses the AT&F1 reset command to choose the factory defaults.
#
This set up is for modems with extended (&) commands and which do not work
#
properly with setup Fð.
For early vintage modems, setup Z or Zð is
#
recommended.
#
# \ Trademark of Hayes Microcomputer Products, Inc.
#
# (C) COPYRIGHT International Business Machines Corp. 1996
# All Rights Reserved
# Licensed Materials - Property of IBM
#
# US Government Users Restricted Rights - Use, duplication or
# disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
#
#
# If the modem has configuration switches, they should be set to the
# factory default settings.
ICDelay 1
DefaultTO 1ð
CallDelay 12ð
# AT Attention Code
,
Inserts delay in dialing commands
# &F1
Reset. Restore profile 1 Qð
Turn on responses
# Eð Turn echo off
Q1
Turn off responses
# Vð Use numeric responses
Sð=ð Automatic answer inhibit
# +++
Escape to command mode
Sð=2 Answer on second ring
# Hð Hang-up
Xð=ð Limit modem response codes
#
T =
Tone mode.
When used as T\r, it is a
#
no op to maintain program synchronization
#
when modem may/will echo the commands.
#
# &C1
Detect CD
&D2
Respond to DTR (often the default)
# &R1
Ignore RTS (CTS)
#
# %N Call-Out phone number
%P
Paging phone number
# %S Modem speed (available to users)
#
# Following are common responses from a wide range of modems:
# 16, 15, 12, 1ð, 5 and 1 are connection responses.
Add others as required.
# 7=busy; 6=no dial tone; 4=error; 3=no carrier; 2=ring; ð=OK
#
# PROGRAMMING NOTE: No blanks between double quote marks (").
condout:
send "AT&F1QðT\r"
# Reset modem. Select profile 1
ignore "ð\r" or "OK\r\n" timeout 2
# Ignore modem response.
send "ATEðT\r"
# Initialize modem: Echo OFF,
expect "ð\r" or "OK\r\n" timeout 2
#
Enable responses (Numeric),
send "ATQðVðXðT\r"
#
Limit response codes.
expect "ð\r" timeout 2
# Confirm commands successful.
send "ATSð=ð\r"
# Set AutoAnswer OFF
expect "ð\r" timeout 2
# Confirm command successful.
send "AT&C1&D2&R1\r"
# Detect carrier and DTR,
#
Ignore RTS.
expect "ð\r" timeout 2
# Confirm command successful.
done
connect:
send "ATDT%N\r"
# Tone dialing command.
# %N from Call Home setup.
# Expect a connection response.
expect "16\r" or "15\r" or "14\r" or "12\r" or "1ð\r" or "5\r" or "1\r" busy "7\r"
Appendix C. Modem Configurations
C-25
Summary of Contents for H SERIES RS/6000
