7.
Set
any
jumpers
or
switches
on
the
drive
according
to
the
documentation
that
comes
with
the
drive.
Note:
You
might
find
it
easier
to
install
the
new
drive
into
the
appropriate
opening
on
the
front,
and
then
attach
the
cables.
8.
If
you
are
installing
a
5.25-in.
drive
in
bay
2,
push
the
drive
into
the
bay;
then,
use
the
two
screws
to
attach
the
drive
to
the
drive
cage.
If
you
are
installing
a
3.5-in.
drive
in
bay
2,
you
must
attach
the
5.25-in.
conversion
kit,
supplied
with
your
option,
to
the
3.5-in.
drive.
9.
Determine
whether
the
drive
is
an
IDE
or
SCSI
device;
then,
connect
one
end
of
the
appropriate
signal
cable
into
the
back
of
the
drive
and
make
sure
that
the
other
end
of
this
cable
is
connected
into
the
appropriate
IDE
or
SCSI
connector
on
the
system
board.
See
“Power
and
signal
cables
for
internal
drives”
on
page
25
for
additional
information
about
cabling
drives
and
“System-board
internal
connectors”
on
page
12
for
the
location
of
IDE
and
SCSI
connectors
on
the
system
board.
If
there
are
open
connectors
on
the
cables
connecting
an
existing
IDE
drive,
this
cable
can
be
used
to
connect
the
new
drive.
The
3-connector
SCSI
cable
that
comes
with
your
computer
cannot
be
used
to
connect
a
SCSI
drive
in
bay
2.
10.
Route
the
signal
cable
so
that
it
does
not
block
the
air
flow
to
the
rear
of
the
drives,
or
over
the
microprocessor
and
memory.
11.
Connect
the
power
cable
to
the
back
of
the
drive.
The
connectors
are
keyed
and
can
be
inserted
only
one
way.
12.
If
you
have
other
options
to
install
or
remove,
do
so
now;
otherwise
replace
the
support
bracket
and
then
go
to
“Completing
the
installation”
on
page
32.
Installing
a
hard
disk
drive
in
bay
4,
5,
or
6
Bays
4,
5,
and
6
are
in
the
drive
cage.
The
drive
cage
is
behind
the
front
of
the
adapter-support
bracket.
Note:
You
might
find
it
useful
to
work
with
the
computer
laying
on
its
side.
Complete
the
following
steps
to
install
a
drive
in
bay
4,
5,
or
6:
1.
Follow
the
instructions
in
“Preinstallation
steps”
on
page
21.
2.
Turn
off
the
computer
and
all
attached
devices
(see
“Turning
off
the
computer”
on
page
36);
then,
disconnect
all
power
cords
and
external
cables.
3.
Remove
the
side
cover
(see
“Removing
the
side
cover”
on
page
14).
4.
Remove
the
support
bracket
(see
“Removing
and
installing
the
support
bracket”
on
page
15).
Chapter
2.
Installing
the
hardware
23
Summary of Contents for IntelliStation Z Pro 6221
