9.
Is
the
SRC
1xxx-1510
or
1910?
v
No
:
Continue
with
the
next
step.
v
Yes
:
Perform
the
following:
a.
See
for
the
model
you
are
working
on
to
determine
the
location
of
power
supply
P01
(SRC
1xxx
1510)
or
PP1
(SRC
1xxx
1910),
and
the
AC
module
it
is
connected
to.
b.
Locate
the
ac
line
cord
that
connects
to
this
AC
module.
Attention:
Do
not
disconnect
the
other
system
line
cord
when
powered
on.
c.
Go
to
step
10.
Is
the
SRC
1xxx-1520
or
1920?
v
No
:
Continue
with
the
next
step.
v
Yes
:
Perform
the
following:
a.
See
for
the
model
you
are
working
on
to
determine
the
location
of
Power
supply
P02
(SRC
1xxx
1520)
or
PP2
(SRC
1xxx
1920)
and
the
AC
module
it
is
connected
to.
b.
Locate
the
ac
line
cord
that
connects
to
this
AC
module.
Attention:
Do
not
disconnect
the
other
system
line
cord
when
powered
on.
c.
Go
to
step
.
11.
Perform
the
following
for
SRC
1xxx-1500,
1510,
1520,
or
1530:
a.
Determine
the
following
AC
module
locations:
v
FC
5074,
FC
5079
(See
or
–
(SRC
1xxx
1510):
the
ac
jumper
cord
connected
to
P01
and
the
AC
module.
–
(SRC
1xxx
1520):
the
ac
jumper
cord
connected
to
P02
and
the
AC
module.
v
FC
5078,
FC
0578
(See
–
(SRC
1xxx
1510):
the
ac
jumper
cord
connected
to
P02
and
the
AC
module.
–
(SRC
1xxx
1520):
the
ac
jumper
cord
connected
to
P01
and
the
AC
module.
v
FC
5088,
FC
0588
(See
–
(SRC
1xxx
1510):
the
ac
jumper
cord
connected
to
power
supply
P02
and
the
AC
module.
–
(SRC
1xxx
1520):
the
ac
jumper
cord
connected
to
power
supply
P01
and
the
AC
module.
v
FC
5095,
FC
0595
(See
–
(SRC
1xxx
1510):
ac
line
cord
1
–
(SRC
1xxx
1520):
ac
line
cord
2.
v
FC
5094
(See
–
(SRC
1xxx
1500):
the
ac
jumper
cord
connected
to
P00
and
the
AC
module.
–
(SRC
1xxx
1510):
the
ac
jumper
cord
connected
to
P01
and
the
AC
module.
–
(SRC
1xxx
1520):
the
ac
jumper
cord
connected
to
P02
and
the
AC
module.
–
(SRC
1xxx
1530):
the
ac
jumper
cord
connected
to
P03
and
the
AC
module.
b.
Continue
with
the
next
step.
12.
Perform
the
following:
DANGER
Dangerous
voltage
being
measured.
(RSFTD005)
a.
Disconnect
the
ac
line
cord
identified
in
the
previous
step
from
the
AC
module.
b.
Use
a
multimeter
to
measure
the
ac
voltage
at
the
AC
module
end
of
the
ac
line
cord.
184
iSeries:
iSeries
Server
270,
800,
810,
820,
825,
830,
840,
870,
890,
SB2,
and
SB3
Hardware
Problem
Analysis
and
Isolation
