Bus-PIP9:
For
use
by
authorized
service
providers.
You
will
need
to
perform
Bus-PIP9
on
an
SPD
migrated
tower.
Go
to
for
more
information.
Bus-PIP10:
For
use
by
authorized
service
providers.
You
will
need
to
perform
Bus-PIP10
on
an
SPD
migrated
tower.
Go
to
for
more
information.
Bus-PIP11:
For
use
by
authorized
service
providers.
You
will
need
to
perform
Bus-PIP11
on
an
SPD
migrated
tower.
Go
to
for
more
information.
Bus-PIPs
for
migrated
towers:
For
use
by
authorized
service
providers.
The
failure
is
in
a
migrated
tower.
SPD
migrated
towers
are
connected
with
a
high-speed
link
and
have
bus
numbers
0004
through
0017
(hexadecimal)
or
4
through
23
(decimal).
Use
Hardware
Service
Manager
(HSM),
the
System
Configuration
Listing,
or
visually
inspect
the
SPD
migrated
I/O
tower
to
determine
the
feature
code
of
the
tower.
Record
the
tower’s
feature
code
number.
You
will
need
the
manual
on
the
V5R1
Supplemental
Manuals
web
site
to
continue.
Go
to
Bus
PIP
Entry
Point
in
the
Bus
Problem
Isolation
Procedures
section
in
the
manual
on
the
V5R1
Supplemental
Manuals
web
site
.
Follow
the
instructions
to
get
to
the
Bus-PIP
that
you
were
sent
there
to
perform
using
the
migrated
tower
feature
code
that
you
recorded.
Bus
PIP
CNSL01:
For
use
by
authorized
service
providers.
Use
this
procedure
to
exchange
the
I/O
processor
for
the
system
or
partition
console.
1.
Does
the
system
have
multiple
partitions?
v
No
:
Go
to
step
8
(See
page
.
v
Yes
:
Is
the
problem
on
a
secondary
partition?
–
Yes
:
Continue
with
the
next
step.
–
No
:
Go
to
step
8
(See
page
.
2.
Can
the
customer
power
off
the
partition
at
this
time?
v
Yes
:
Power
down
the
partition
from
the
Primary
partition’s
Work
with
partition
status
display.
Then,
continue
with
the
next
step.
v
No
:
The
IOP
controlling
the
partition’s
console
may
be
controlling
other
critical
resources.
The
partition
must
be
powered
off
to
exchange
this
IOP.
Perform
this
procedure
when
the
customer
is
able
to
power
down
the
partition
from
the
Primary
partition’s
Work
with
partition
status
display.
Then,
continue
with
the
next
step.
3.
Determine
the
logical
address
and
the
frame
ID
of
the
console
IOP
using
the
following
steps:
a.
In
SST/DST,
select
Work
with
System
Partitions
—>
Display
partition
information
—>
Display
allocated
I/O
resources
.
b.
Page
down
until
you
find
the
console
IOP
for
the
partition
that
you
are
working
with.
c.
Select
Display
logical
address
.
d.
Record
the
bus,
card
and
board
logical
address
for
the
console’s
IOP.
Analyze
hardware
problems
77
