background image

v

Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.

v

See Chapter 3, “Parts listing, Type 8850,” on page 53 to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).

v

If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.

Error code

Description

Action

01295085

ECC-checking hardware test error.

1. (Trained service technician only) Reseat the

microprocessor.

2. Replace the following components one at a time,

in the order shown, restarting the server each
time.

a. (Trained service technician only) System

board assembly

b. (Trained service technician only)

Microprocessor

012980xx

Patch code missing.

1. Flash the BIOS code.

2. (Trained service technician only) Reseat

microprocessor x.

3. (Trained service technician only) Replace

microprocessor x.

012981xx

Processor patch (microcode) update failed.

1. Flash the BIOS code.

2. (Trained service technician only) Reseat

microprocessor x.

3. (Trained service technician only) Replace

microprocessor x.

01298200

Processor speed mismatch.

Make sure that microprocessors 1 and 2 have the
same number of cores, cache size and type, clock
speed, internal and external clock frequencies (see
“Configuration/Setup Utility menu choices” on page
87).

19990301

Hard disk sector error.

1. Reseat the hard disk drive.

2. Replace the following components one at a time,

in the order shown, restarting the server each
time.

a. Hard disk drive

b. (Trained service technician only) System

board assembly

19990305

An operating system was not found.

1. Make sure that a bootable operating system is

installed.

2. Run the Fixed Disk diagnostic test.

3. Reseat the hard disk drive.

4. Replace the following components one at a time,

in the order shown, restarting the server each
time.

a. Hard disk drive

b. (Trained service technician only) System

board assembly

Chapter 2. Diagnostics

25

Summary of Contents for LS20 - BladeCenter - 8850





















































































































Reviews: