v
Test the Ethernet controller.
The way you test the Ethernet controller depends on which operating system
you are using (see the Ethernet controller device driver README file).
Ethernet controller troubleshooting chart
You can use the following troubleshooting chart to find solutions to 10/100 Mbps
Ethernet controller problems that have definite symptoms.
Table 5. Ethernet troubleshooting chart
Ethernet controller problem
Suggested Action
The system stops running
when loading device drivers.
The PCI BIOS interrupt settings are incorrect.
Check the following:
v
Determine if the IRQ setting assigned to the Ethernet controller is also assigned to
another device in the Configuration/Setup Utility program.
Although interrupt sharing is allowed for PCI devices, some devices do not
function well when they share an interrupt with a dissimilar PCI device. Try
changing the IRQ assigned to the Ethernet controller or the other device. For
example, for NetWare Versions 3 and 4 it is recommended that disk controllers not
share interrupts with LAN controllers.
v
Make sure that you are using the most recent device driver available from the
World Wide Web.
v
Run the network diagnostic program.
If the problem remains, call for service.
The LAN activity light (some
models) does not light.
Check the following:
v
Make sure that you have loaded the network device drivers.
v
The network might be idle. Try sending data from this workstation.
v
Run diagnostics on the LEDs.
v
The function of this LED can be changed by device driver load parameters. If
necessary, remove any LED parameter settings when you load the device drivers.
Data is incorrect or sporadic.
Check the following:
v
Make sure that you are using Category 5 cabling when operating the system at
100 Mbps.
v
Make sure that the cables do not run close to noise-inducing sources like
fluorescent lights.
The Ethernet controller
stopped working when
another adapter was added
to the system.
Check the following:
v
Make sure that the cable is connected to the Ethernet controller.
v
Make sure that your PCI system BIOS is current.
v
Reseat the adapter.
v
Determine if the IRQ setting assigned to the Ethernet adapter is also assigned to
another device in the Configuration/Setup Utility program.
Although interrupt sharing is allowed for PCI devices, some devices do not
function well when they share an interrupt with a dissimilar PCI device. Try
changing the IRQ assigned to the Ethernet adapter or the other device.
If the problem remains, call for service.
The Ethernet controller
stopped working without
apparent cause.
Check the following:
v
Run diagnostics for the Ethernet controller.
v
Try a different connector on the hub.
v
Reinstall the device drivers. Refer to your operating system documentation.
If the problem remains, call for service.
94
IBM
®
IntelliStation
®
E Pro: User’s Guide IntelliStation E Pro Types 6836, 6846
Summary of Contents for NetVista X40
