18.
On
a
Model
6C3,
route
the
cables
through
the
cable-management
arm.
19.
Replace
the
service
access
cover
as
described
in
“Replacing
the
Model
6C3
Service
Access
Cover”
on
page
288
or
“Replacing
the
Model
6E3
Service
Access
Cover”
on
page
289.
20.
Reconnect
any
cables
connected
to
the
PCI
adapter
at
the
rear
of
the
system.
21.
Reconnect
the
power
source
to
the
system.
22.
Return
the
system
to
the
operating
position
as
described
in
“Returning
the
Model
6C3
to
the
Operating
Position”
on
page
285
or
“Placing
the
Model
6E3
into
the
Service
and
Operating
Position”
on
page
286.
23.
On
a
Model
6C3,
close
the
rear
rack
door.
24.
Start
the
system
as
described
in
“Starting
the
System”
on
page
283.
Replacing
or
Installing
a
Non-Hot-Pluggable
PCI
Adapter
To
replace
or
install
an
non-hot-pluggable
adapter,
do
the
following:
1.
Stop
the
system
as
described
in
“Stopping
the
System”
on
page
282.
2.
Disconnect
the
power
source
to
the
system.
Note:
This
system
may
be
equipped
with
a
second
power
supply.
Before
continuing
with
this
procedure,
ensure
that
the
system
has
been
completely
disconnected
from
its
power
source.
3.
If
necessary,
disconnect
any
cables
connected
to
the
PCI
adapter
at
the
rear
of
the
system.
4.
Place
the
system
into
the
service
position
as
described
in
“Placing
the
Model
6C3
into
the
Service
Position”
on
page
284
or
“Placing
the
Model
6E3
into
the
Service
and
Operating
Position”
on
page
286.
5.
On
a
Model
6C3,
open
the
rear
rack
door.
6.
Remove
the
service
access
cover
as
described
in
“Removing
the
Model
6C3
Service
Access
Cover”
on
page
288
or
“Removing
the
Model
6E3
Service
Access
Cover”
on
page
289.
7.
Refer
to
the
RS/6000
&
pSeries
PCI
Adapter
Placement
Reference
,
order
number
SA38-0538,
for
information
regarding
slot
restrictions
for
adapters
that
can
be
used
in
this
system.
8.
If
necessary,
remove
the
adapter
slot
shield.
9.
Before
handling
any
card,
board,
or
memory
DIMM,
refer
to
“Handling
Static-Sensitive
Devices”
on
page
280.
10.
If
necessary,
remove
the
adapter
from
the
antistatic
package.
Attention:
Avoid
touching
the
components
and
gold-edge
connectors
on
the
adapter.
11.
Place
the
adapter,
component-side
up,
on
a
flat,
static-protective
surface.
12.
Set
any
jumpers
or
switches
as
instructed
by
the
adapter’s
manufacturer.
13.
Carefully
grasp
the
adapter
by
its
top
edge,
and
align
the
adapter
with
the
adapter
slot
and
its
connector
on
the
system
backplane.
14.
Press
the
adapter
firmly
into
its
connector.
Attention:
When
you
install
an
adapter
into
the
system,
be
sure
that
it
is
completely
and
correctly
seated
in
its
connector.
15.
If
you
are
replacing
or
installing
a
short
adapter,
continue
to
the
next
step.
If
you
are
replacing
or
installing
a
long
adapter,
do
the
following:
a.
Close
and
latch
the
PCI
adapter
light-pipe
plate
attached
to
the
fan
tray.
b.
Note
the
guide
grooves
located
toward
the
front
of
the
system
in
the
disk
drive
backplane,
and
align
the
adapter
properly.
296
Eserver
pSeries
615
Service
Guide
Summary of Contents for P 615 series
