9.
Visually
check
to
ensure
that
the
cassette
is
parallel
with
the
cassettes
to
the
left
or
right.
If
the
cassette
is
not
parallel
with
the
neighboring
cassettes,
the
cassette
dovetail
rails
might
not
be
correctly
engaged.
If
the
cassette
is
not
correctly
aligned,
you
might
need
to
pull
it
out
so
you
can
see
the
ends
of
the
dovetail
rails.
If
so,
reinsert
the
cassette,
ensuring
that
the
dovetail
rails
engage
on
both
sides
of
the
cassette.
Note:
If
there
are
no
other
cassettes
installed,
it
is
not
necessary
to
check
the
alignment
of
the
dovetail
rails.
10.
Depress
the
handle
release
latch.
Lift
the
handle
up
until
the
handle-release
lever
clicks
when
it
locks
into
position.
Note:
To
aid
you
in
seating
the
PCI
adapter
connector,
it
may
be
necessary
to
press
down
on
the
adapter
tailstock
tab.
The
PCI
adapter
is
completely
installed
into
the
PCI
adapter
slot
when
the
handle
is
in
the
fully
raised
position
and
the
tailstock
is
seated
into
the
slots
located
on
the
system
board.
Attention:
Do
not
force
the
handle
into
the
raised
position.
Removing
a
Non-Hot-Pluggable
PCI
Adapter
To
remove
a
non-hot-pluggable
adapter,
do
the
following:
1.
Turn
off
power
and
remove
the
power
from
the
system.
2.
Determine
the
slot
from
which
you
are
removing
the
adapter.
3.
Refer
to
“Removing
a
PCI
Adapter
Cassette”
on
page
128.
When
you
have
completed
the
PCI
adapter
cassette
removal
procedure,
return
here.
4.
If
you
are
installing
another
adapter
in
this
slot,
follow
the
instructions
given
in
“Replacing
a
Non-Hot-Pluggable
PCI
Adapter.”
If
you
are
not
installing
another
adapter
in
this
slot,
install
a
blank
PCI
adapter
cassette
into
the
slot.
Refer
to
“Replacing
a
PCI
Adapter
Cassette”
on
page
131.
5.
Connect
power
to
the
system
and
turn
the
power
on.
6.
Return
the
system
to
normal
operations.
Replacing
a
Non-Hot-Pluggable
PCI
Adapter
Replace
the
adapter
using
the
following
procedure:
Note:
Because
the
adapter
you
are
installing
is
not
hot-pluggable,
shut
down
the
system
and
remove
power
before
performing
this
procedure.
1.
If
you
have
just
removed
an
adapter
and
you
are
replacing
it
in
the
system,
use
the
procedures
in
“PCI
Adapter
or
Blank
Filler
Removal
from
a
Snap-Assembly-Type
Cassette”
on
page
140
to
install
the
replacement
adapter
into
the
PCI
adapter
cassette.
2.
Go
to
“Replacing
a
PCI
Adapter
Cassette”
on
page
131
to
replace
the
appropriate
cassette
in
the
PCI
slot,
then
return
here.
3.
Connect
power
to
the
system.
4.
Return
the
system
to
normal
operations.
5.
Set
the
color
slide
to
blue.
6.
Ensure
that
the
adapter
is
configured
when
the
system
completes
the
boot
process.
Appendix
C.
Removing
and
Replacing
PCI
Adapters
133
Summary of Contents for p 655 series
