15.
At
the
rear
of
the
rack,
tighten
the
two
knurled
captive
screws
at
the
bottom
of
the
chassis,
to
hold
the
processor
subsystem
to
the
frame
cage.
16.
Route
and
connect
all
cables
previously
removed
from
the
processor
subsystem.
These
may
include:
v
Power
cables
to
the
DCA
units
on
the
front
of
the
subsystem
v
RIO
cables
at
the
rear
of
the
subsystem
v
PCI
adapter
cables
at
the
rear
of
the
subsystem
v
Serial
cables
at
the
rear
of
the
subsystem
v
Ethernet
cables
at
the
rear
of
the
subsystem
17.
If
additional
service
is
not
being
performed,
close
the
rack
doors.
18.
Repackage
the
lift
tool.
Processor
Subsystem
Removal
CAUTION:
This
unit
weighs
between
32
kg
(70.5
pounds)
and
55
kg
(121.2
pounds).
Three
persons
are
required
to
safely
move
it.
Using
less
than
three
persons
to
move
it
can
result
in
injury.
C05
Attention:
Removing
a
processor
subsystem
for
the
rack
requires
the
use
of
a
lift
tool.
This
procedure
requires:
v
The
use
of
a
lift
tool
(part
number
09P2481)
and
lift-plate
assembly
tool
(part
number
11P4369).
v
The
lift
tool
wheels
must
be
chocked
to
prevent
it
from
moving
during
the
operation.
The
rack
must
not
be
on
its
casters.
The
leveling
pads
must
be
engaged
to
prevent
the
rack
from
moving
during
the
operation.
To
remove
the
processor
subsystem
from
the
rack,
do
the
following:
1.
Ensure
that
power
to
the
system
is
turned
off.
2.
Open
the
front
and
rear
doors
of
the
rack.
3.
Prepare
the
lift
tool
for
use
as
follows:
a.
Unpack
the
lift
tool
and
follow
the
assembly
instructions
included
with
the
tool.
b.
Inspect
the
tool
for
damage
(do
not
perform
the
removal
procedure
with
a
damaged
lift
tool).
c.
Read
all
safety
instructions
before
performing
this
operation.
d.
Replace
the
blue
lift
plate
with
the
orange
lift
plate
(part
number
11P4369).
e.
Orient
the
two
round
holes
in
the
lift
plate
to
the
side
of
the
lift
tool
that
will
be
closest
to
the
rack.
4.
Label
all
cables
and
components,
and
record
their
locations
at
the
front
and
the
rear
of
the
rack.
5.
Disconnect
all
cables
on
the
processor
subsystem.
These
may
include:
v
Power
cables
to
the
DCAs
on
the
front
of
the
subsystem
v
RIO
cables
at
the
rear
of
the
subsystem
v
PCI
adapter
cables
at
the
rear
of
the
subsystem
v
Serial
cables
at
the
rear
of
the
subsystem
v
Ethernet
cables
at
the
rear
of
the
subsystem
6.
At
the
rear
of
the
rack,
loosen
the
two
knurled
captive
screws,
at
the
bottom
of
the
chassis,
holding
the
processor
subsystem
to
the
frame
cage.
Note:
The
nuts
are
on
captive
screws
and
are
not
removed
from
the
chassis
when
removing
the
processor
subsystem.
7.
At
the
front
of
the
rack,
lift
the
front
cover
on
the
frame
cage
and
lock
it
into
the
open
position.
8.
To
remove
the
processor
subsystem
from
the
rack,
use
the
lift
tool,
and
do
the
following:
Chapter
4.
Installation
and
Removal
Procedures
43
Summary of Contents for pseries 655
