14.
Remove
the
wheel
chocks
on
the
lift-tool
casters,
and
release
the
lift-tool
brake.
15.
Move
the
lift
tool
with
the
I/O
subsystem
to
a
staging
area,
and
move
the
I/O
subsystem
from
the
lift
plate.
16.
Install
the
wheel
chocks
on
the
lift-tool
casters,
and
engage
the
lift-tool
brake.
17.
Position
the
I/O
subsystem
on
a
sturdy
and
stable
work
surface.
18.
If
other
subsystems
are
not
being
installed
or
removed,
repackage
the
lift
tool.
Integrated
Battery
Feature
(IBF)
This
section
describes
how
to
install
and
remove
the
integrated
battery
feature.
Integrated
Battery
Feature
Installation
CAUTION:
This
unit
weighs
between
32
kg
(70.5
pounds)
and
55
kg
(121.2
pounds).
Three
persons
are
required
to
safely
move
it.
Using
less
than
three
persons
to
move
it
can
result
in
injury.
C05
Attention:
Installing
an
IBF
in
the
rack
requires
the
use
of
a
lift
tool.
This
procedure
requires:
v
The
use
of
a
lift
tool
(part
number
09P2481)
and
lift-plate
assembly
tool
(part
number
11P4369).
v
The
lift
tool
wheels
must
be
chocked
to
prevent
it
from
moving
during
the
operation.
The
rack
must
not
be
on
its
casters.
The
leveling
pads
must
be
engaged
to
prevent
the
rack
from
moving
during
the
operation.
To
install
an
IBF,
do
the
following:
1.
Unpack
the
lift
tool
and
follow
assembly
instructions
included
with
the
tool.
2.
Inspect
the
tool
for
damage
(do
not
perform
the
installation
procedure
with
a
damaged
lift
tool).
3.
Read
all
safety
instructions
before
performing
this
operation.
4.
Replace
the
blue
lift
plate
with
the
orange
lift
plate
(part
number
11P4369).
5.
Orient
the
two
round
holes
in
the
lift
plate
to
the
side
of
the
lift
tool
that
will
be
closest
to
the
frame.
6.
Position
the
lift
tool
so
that
the
IBF
can
be
moved
onto
the
lift
plate.
Note:
The
lift-tool
extension
arms
are
not
attached
to
the
rack
for
this
system.
7.
Install
the
wheel
chocks,
and
engage
the
brake
on
the
lift
tool.
8.
Move
the
IBF
onto
the
tool
with
the
rear
side
toward
the
two
holes
of
the
lift
plate.
The
side
with
the
handles
is
considered
the
front
side.
Note:
Ensure
that
the
IBF
is
in
the
center
of
the
lift
plate.
9.
Remove
the
wheel
chocks
on
the
lift-tool
casters,
and
disengage
the
lift-tool
brake.
10.
Position
the
lift
tool
as
close
as
possible
to
the
rack.
11.
Install
the
wheel
chocks,
and
engage
the
brake
on
the
lift
tool.
12.
Raise
the
lift
plate
to
a
height
so
that
the
lift
plate
is
just
above
the
rails
of
the
slot
you
are
installing
it
in.
Note:
Ensure
that
the
IBF
is
being
installed
in
its
original
rack
location.
13.
Push
the
IBF
into
the
frame.
Adjust
the
height
of
the
lift
plate,
as
needed.
14.
Lower
the
lift
plate
on
the
lift
tool.
15.
Fasten
the
IBF
to
the
mounting
rails,
using
the
mounting
screws.
16.
Install
the
battery
cable
in
the
IBF
cable
connector.
Chapter
4.
Installation
and
Removal
Procedures
47
Summary of Contents for pseries 655
