17.
Fasten
the
cable
retaining
clamp
(closest
to
the
cable’s
connector)
to
the
frame,
using
the
retaining
clamp
screw.
18.
If
other
subsystems
are
not
being
installed,
repackage
the
lift
tool.
Integrated
Battery
Feature
Removal
CAUTION:
This
unit
weighs
between
32
kg
(70.5
pounds)
and
55
kg
(121.2
pounds).
Three
persons
are
required
to
safely
move
it.
Using
less
than
three
persons
to
move
it
can
result
in
injury.
C05
Attention:
Removing
an
IBF
the
rack
requires
the
use
of
a
lift
tool.
This
procedure
requires:
v
The
use
of
a
lift
tool
(part
number
09P2481)
and
lift-plate
assembly
tool
(part
number
11P4369).
v
The
lift
tool
wheels
must
be
chocked
to
prevent
it
from
moving
during
the
operation.
The
rack
must
not
be
on
its
casters.
The
leveling
pads
must
be
engaged
to
prevent
the
rack
from
moving
during
the
operation.
To
remove
an
IBF,
do
the
following:
1.
Unpack
the
lift
tool
and
follow
assembly
instructions
included
with
the
tool.
2.
Inspect
the
tool
for
damage
(do
not
perform
the
removal
procedure
with
a
damaged
lift
tool).
3.
Read
all
safety
instructions
before
performing
this
operation.
4.
Replace
the
blue
lift
plate
with
the
orange
lift
plate
(part
number
11P4369).
5.
Orient
the
two
round
holes
in
the
lift
plate
to
the
side
of
the
lift
tool
that
will
be
closest
to
the
frame.
6.
Locate
the
IBF
to
be
removed.
7.
Remove
the
battery
cable
from
the
front
of
the
IBF,
and
remove
the
screw
(closest
to
the
connector)
holding
the
cable
to
the
rack.
This
action
allows
the
cable
to
move
so
the
IBF
can
be
removed.
8.
Remove
the
two
mounting
screws
from
the
top
and
bottom
guide
rails
and
retain
for
reuse.
9.
Raise
the
lift
plate
to
a
height
so
that
the
lift
plate
is
just
below
the
base
of
the
IBF
you
are
removing.
10.
Lock
the
lift
plate
in
place.
11.
Pull
and
guide
the
IBF
onto
the
lift
plate.
The
IBF
must
be
removed
far
enough
to
clear
the
front
face
of
the
rack.
Retract
the
extender
arms
and
the
center
portion
of
the
lift
plate.
Note:
Ensure
that
the
IBF
is
in
the
center
of
the
lift
plate.
12.
Lower
the
IBF
to
the
bottom
position
of
the
lift
tool.
13.
Remove
the
wheel
chocks
on
the
lift-tool
casters,
and
release
the
lift-tool
brake.
14.
Move
the
lift
tool
with
the
IBF
to
a
staging
area.
15.
Position
the
IBF
on
a
sturdy
and
stable
work
surface.
16.
If
other
subsystems
are
not
being
installed
or
removed,
repackage
the
lift
tool.
48
Eserver
pSeries
655
Installation
Guide
Summary of Contents for pseries 655
