DRAFT
administrator
and
are
performing
a
flash
update
using
the
IBM
Remote
Deployment
Manager
software,
download
the
LCCM
Bios
update
.
2.
Ensure
that
the
formatted
diskette
is
not
write
protected,
and
insert
the
diskette.
3.
Browse
to
the
location
of
the
downloaded
BIOS
flash
image
and
double-click
on
the
executable
file
4.
Follow
the
on-screen
instructions
to
create
the
bootable
BIOS
diskette.
Note:
If
you
encounter
problems
with
creating
the
diskette,
try
another
diskette
or
another
PC
to
create
the
diskette.
You
can
also
download
the
image
from
the
Internet
again.
5.
Insert
the
diskette
into
the
diskette
drive,
power
on
the
machine,
and
allow
it
to
boot
using
the
diskette.
The
system
will
automatically
power
off
when
the
BIOS
update
is
complete.
Note:
If
you
encounter
problems
getting
the
diskette
to
boot
the
system,
remove
the
diskette,
reboot
and
follow
the
steps
“Steps
to
enter
setup
and
change
the
first
boot
device”
on
page
1
to
ensure
that
the
floppy
diskette
drive
(FDD)
is
enabled
as
a
boot
device.
Partitioning
the
hard
disk
You
can
partition
the
hard
disk
by
using
the
FDISK
and
FORMAT
utilities.
Note:
Use
the
version
of
FDISK
on
the
PC
DOS
2000
diskettes.
1.
Boot
the
system
from
the
DOS
Network/CD-ROM
Boot
Disk.
2.
At
the
command
prompt,
type
FDISK
and
press
Enter
.
3.
FDISK
will
ask
if
large
disk
support
should
be
enabled.
For
Windows
NT
®
4.0,
choose
N
.
For
Windows
2000
and
Windows
XP,
choose
Y
.
4.
When
the
FDISK
Options
menu
appears,
press
4
then
press
Enter
.
This
will
display
all
partitions
defined
in
the
partition
table.
5.
Record
all
partitions
and
their
types.
Press
Esc
when
finished.
6.
To
delete
all
partitions
defined
in
the
partition
table,
press
3
then
press
Enter
.
A
menu
will
appear
which
allows
the
partitions
to
be
deleted.
Each
partition
must
be
deleted
individually.
7.
After
the
deletion
of
all
partitions,
a
new
primary
DOS
partition
must
be
created.
At
the
FDISK
Options
menu,
press
1
and
then
Enter
.
8.
Once
the
Create
DOS
Partition
or
Logical
DOS
Drive
menu
has
appeared,
press
1
then
press
Enter
.
9.
In
a
few
moments,
the
next
menu
will
appear.
The
system
will
ask
if
all
available
space
should
be
used
for
the
installation
and
if
it
should
make
the
partition
active.
Press
Y
for
yes
then
press
Enter
.
10.
Press
any
key
to
restart
the
system.
11.
Repeat
Steps
1
and
2
of
this
procedure.
12.
After
the
command
prompt
appears,
type
format
c:
/u
.
This
will
perform
an
unconditional
format.
13.
The
question
Proceed
with
Format?
will
appear.
Press
Y
for
yes.
14.
After
formatting
completes,
enter
a
volume
label.
15.
Clear
the
master
boot
record
to
ensure
that
any
previous
boot
loaders
are
removed.
This
can
be
done
by
typing
fdisk
/mbr
from
the
command
prompt.
16.
Restart
the
system.
Updated
October,
2007
2
SurePOS
700
Series:
SurePOS
700-722/742/782,
723/743/783
Operating
System
Installation
Guide
