9.
Remove the cartridge from the cartridge loader tray.
10.
Go to “Ending Procedure.”
Ending Procedure
1.
Reassemble the drive brick by reversing the steps in “Removing the Drive
Cover” on page A-6.
2.
Reassemble the drive sled by performing the following steps:
a.
Reinstall the drive brick into the sled by performing the following steps:
v
Plug in the RS-422 cable, the power cable (if applicable), and the signal
cable.
v
Push the drive brick fully into the sled.
v
Align the two screws holes on each side of the sled with the screw holes
on each side of the drive brick. DO NOT TIGHTEN THE SCREWS
COMPLETELY.
v
After verifying that the drive and sled are properly aligned, fully tighten
the screws.
b.
If necessary, perform the following steps to reinstall the connection card and
protective plastic cover on the sled.
v
Place the card and the protective plastic cover on top of spacers aligning
the three screw holes. DO NOT TIGHTEN THE SCREWS COMPLETELY.
v
After verifying that the connection card and protective plastic cover are
properly aligned, fully tighten the three screws.
3.
Install the tape drive sled in the library. Refer to “Installing a Tape Drive Sled”
on page 10-6.
4.
Power ON the library and wait for the library to finish POST (power on self
test), inventory and mid-tape recovery (this can take up to 1 hour).
5.
If the cartridge does not eject from the drive, move the cartridge from the drive
to the I/O Station (Operator Control Panel:
Control
>
Move Cartridges
; Web
User Interface:
Manage Library
>
Move Media
), then discard the cartridge.
6.
Run Library Verify before resuming normal library operations. Refer to
“Service: Library Verify” on page 5-30.
7.
If necessary, return the failed drive sled to IBM.
Accessing the Library using Telnet
To access a customer's library using telnet, complete the following procedure:
1.
Ask the library administrator to enable the serial port (Operator Control
Panel:
Service
>
Telnet Service Port
).
2.
Open a Windows Command Prompt screen.
3.
Enter
telnet [library IP address]
then press the
Enter
key.
4.
FLMON>
will display.
5.
Enter
lgi
then press the
Enter
key.
6.
Enter
service
as your Username, then press the
Enter
key.
7.
Enter the service Password, then press the
Enter
key. Contact your next level
of support for the password.
8.
Enter
help
then press the
Enter
key for the expanded command menu.
9.
To end the telnet session, enter
lgo
then press the
Enter
key to log out of the
library.
10.
Enter
exit
then press the
Enter
key to disconnect from the library.
Appendix A. Information for Trained Service Personnel
A-25
Summary of Contents for System Storage TS3100
