7.
Enable SSL for Web
- If you desire to have SSL (Secure Sockets Layer)
enabled, place a check in this box.
Note:
If you get a security certificate alert when logging in to the Web User
Interface, you can install the certificate or allow an exception
(depending on the internet browser you are using). SSL is enabled
when the URL begins with
https://
and some browsers will show a
lock.
8.
Ethernet Settings
- Ethernet Settings choices are:
Auto
(the default),
10
Mbit/Half
,
10 Mbit/Full
,
100 Mbit/Half
,
100 Mbit/Full
.
9.
Enter IPv4 settings (if applicable).
a.
Enable DHCP
- Click this item ON to have the IP Address of your library
automatically set by the DHCP server.
b.
Static Address
- Enter the assigned IPv4 address. The format of an IPv4 IP
address is a 32-bit numeric address written as four numbers separated by
periods.
c.
Network Mask
- Enter the assigned IPv4 Network Mask.
d.
Gateway address
- Enter the assigned IPv4 Gateway address. This address
allows access outside the local network.
10.
Enter IPv6 settings (if applicable).
a.
Enable DHCP
- Click this item ON to have the IP Address of your library
automatically set by the DHCP server.
b.
Enable Stateless Auto Config
- Click this item ON to have the IP Address
of your library automatically set by the network router.
c.
Static Address
- Enter the assigned IPv6 address. The format of an IPv6 IP
address is a 128-bit numeric address written as 8 groups of four numbers
separated by colons.
d.
Prefix length
- The default prefix length is set to 64, but can be set to any
length, depending upon the address used.
e.
Gateway address
- Enter the assigned IPv6 Gateway address. This address
allows access outside the local network.
11.
Click one of the following:
v
Refresh
- to cancel the changes made to the screen.
v
Submit
- to apply the changes made to the screen.
Note:
Depending on the changes made, you will either be disconnected and
need to login again, or reboot the library. If a reboot is required, the
following Warning message will appear after the Submit button is
clicked.
The library must be rebooted or the changes will not take place.
Entering User Access Information using the Web User Interface
The
Configure Library
>
User Access
page is only accessible to the Admin and
Service login. Access is denied to User and Superuser logins.
Figure 4-32. Warning Screen
Chapter 4. Installation and Configuration
4-31
Summary of Contents for System Storage TS3100
