4
Module
communication
terminator
9
SCSI
drive-to-host
cable
5
SCSI
terminators
1.
Install
a
module
communication
terminator
in
the
upper
receptacle
of
the
upper
module
of
your
library
(
4
in
2.
Install
one
end
of
the
module-to-module
communication
cable
(
2
in
in
the
lower
receptacle
of
the
upper
module
of
your
library,
then
install
the
other
end
in
the
upper
receptacle
of
the
lower
module
of
your
library.
3.
Install
a
module
communication
terminator
in
the
lower
receptacle
of
the
lower
module
of
your
library
(
1
in
4.
Install
one
end
of
the
customer-supplied
Ethernet
cable
(
3
in
in
the
Library
Control
Blade
Ethernet
port,
then
connect
the
other
end
of
the
cable
to
your
network.
5.
Installation
of
the
SCSI
cable(s)
and
terminator(s)
depends
upon
how
many
drives
are
in
your
library.
v
For
maximum
drive
performance:
v
Install
a
SCSI
terminator
(
5
in
in
the
upper
receptacle
of
each
SCSI
drive
in
your
library.
v
Connect
one
end
of
a
SCSI
cable
to
the
lower
receptacle
of
each
SCSI
drive
(
6
in
then
connect
the
other
end
of
the
cable
to
the
host.
v
If
you
prefer
to
daisy-chain
your
SCSI
drives:
a.
Install
a
SCSI
terminator
in
the
upper
receptacle
of
the
top
SCSI
drive
in
the
daisy-chain.
b.
Connect
one
end
of
a
shorter
drive-to-drive
SCSI
cable
included
in
your
shipment
to
the
lower
receptacle
of
the
top
SCSI
drive
in
the
daisy-chain,
then
connect
the
other
end
of
the
cable
to
the
upper
receptacle
of
the
next
drive
in
the
daisy-chain.
Repeat
this
for
every
SCSI
drive
in
your
library.
c.
On
the
last
drive
in
the
daisy-chain,
connect
one
end
of
the
longer
drive-to-host
SCSI
cable
included
in
your
shipment
to
the
lower
receptacle
of
the
last
drive
in
the
daisy-chain,
then
connect
the
other
end
of
the
cable
to
the
host.
Note:
Maximum
performance
of
the
SCSI
drives
in
your
library
will
not
be
achieved
if
the
drives
are
daisy-chained.
6.
Install
one
end
of
the
power
cord
(
7
and
8
in
in
the
receptacle
of
a
power
supply
in
your
library,
then
connect
the
other
end
of
the
cord
to
your
power
source.
Repeat
this
for
every
power
supply
in
your
library.
7.
Continue
with
Cabling
a
Library
Containing
Fibre
and
SCSI
Drives
To
cable
a
library
containing
both
fibre
and
SCSI
drives,
complete
the
following
steps:
SCSI
and
Fibre
Channel
drives
can
reside
in
the
same
library;
however,
they
can
not
reside
in
the
same
logical
library.
Chapter
3.
Installing
the
Library
3-21
Summary of Contents for System Storage TS3310
