v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
v
See Chapter 4, “Parts listing, System x3100 M4 Type 2582,” on page 151 to determine which components
are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
v
Go to the IBM support website at http://www.ibm.com/supportportal/ to check for technical information,
hints, tips, and new device drivers or to submit a request for information.
Error code
Description
Action
0058001
PFA threshold exceeded.
Note:
Each time you install or remove a DIMM, you
must disconnect the server from the power source;
then, wait 10 seconds before restarting the server.
1. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
2. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor
(see“Installing a memory module” on page 203 for
memory population).
3. If the error still occurs on the same DIMM, replace
the affected DIMM (see “Removing a memory
module” on page 200 and “Installing a memory
module” on page 203).
4. (Trained service technician only) If the problem
occurs on the same DIMM connector, check the
DIMM connector. If the connector contains any
foreign material or is damaged, replace the
system board (see “Removing the system board”
on page 258 and “Installing the system board” on
page 261).
5.
(Trained service technician only) Remove the
affected microprocessor and check the
microprocessor socket pins for any damaged pins.
If a damage is found, replace the system board
(see “Removing the system board” on page 258
and “Installing the system board” on page 261).
6. (Trained Service technician only) Replace the
affected microprocessor (see “Removing the
microprocessor and heat sink” on page 250 and
“Installing a microprocessor and heat sink” on
page 254).
0058007
Unsupported DIMM population.
Note:
Each time you install or remove a DIMM, you
must disconnect the server from the power source;
then, wait 10 seconds before restarting the server.
1. Reseat the DIMMs and restart the server
(see“Removing a memory module” on page 200
and “Installing a memory module” on page 203).
2. Make sure that the DIMMs are installed in the
proper sequence (see “Installing a memory
module” on page 203).
Chapter 3. Diagnostics
33
Summary of Contents for System x3100 M4
