IBM System x3690 X5 Service Manual Download | Manualshive

Page: 30 / 464

background image

Note:

The maximum video resolution is 1280 x 1024 at 75 Hz.

v

USB connectors:

Connect a USB device, such as a USB mouse, keyboard, or

other device to any of these connectors.

Operator information panel

The following illustration shows the controls and LEDs on the operator
information panel.

2

1

Ethernet
activity LEDs

Locator button/
locator LED

Information LED

System-error LED

Release latch

Power-control button/
power-on LED

Power-control
button cover

Ethernet
icon LED

v

Power-control button and power-on LED:

Press this button to turn the server

on and off manually or to wake the server from a reduced-power state. The
states of the power-on LED are as follows:

Off:

AC power is not present, or the power supply or the LED itself has

failed.

Flashing rapidly (4 times per second):

The server is turned off and is not

ready to be turned on. The power-control button is disabled. This lasts
approximately 1 to 3 minutes.

Flashing slowly (once per second):

The server is turned off and is ready to

be turned on. You can press the power-control button to turn on the server.

Lit:

The server is turned on.

Fading on and off:

The server is in a reduced-power state. To wake the

server, press the power-control button or use the IMM Web interface. See
“Logging on to the Web interface” on page 413 for information on logging on
to the IMM Web interface.

v

Ethernet activity LEDs:

When any of these LEDs is flashing or flickering, they

indicate that the server is transmitting to or receiving signals from the Ethernet
LAN that is connected to the Ethernet port that corresponds to that LED.

v

Locator button/LED:

Use this blue LED to visually locate the server among

other servers. This LED is also used as a presence detection button. You can use
IBM Systems Director to light this LED remotely. This LED is controlled by the
IMM. When you press the locator button, the LED will be lit and it will continue
to be lit until you press it again to turn it off. Press the locator button to visually
locate the server among the others servers. In a two-node configuration, this
LED will be lit on the primary server and this LED will blink on the secondary
server during POST, if the button is pressed or an IPMI command is issued to
turn on the LED. It is also used as the physical presence for the Trusted Platform
Module (TPM).

v

Information LED:

When this amber LED is lit, it indicates that a noncritical

event has occurred. Check the system-event log for additional information. See
“Event logs” on page 35 for information about the event logs.

v

System-error LED:

When this amber LED is lit, it indicates that a system error

has occurred. A system-error LED is also on the rear of the server. An LED on

12

System x3690 X5 Types 7147, 7148, 7149, and 7192: Problem Determination and Service Guide

«
...
28
29
30
31
32
...
»

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

LITTLE BIG DISK THUNDERBOLT 2

Brand: LaCie Pages: 6

Garage Gator GGR220

Brand: V-Bro Products Pages: 18

301300U - Ethernet Disk NAS Server

Brand: LaCie Pages: 62

2big Thunderbolt Series 4 TB

Brand: LaCie Pages: 45

Brand: IOGear Pages: 2

ProLiant DL100 G2 DPSS

Brand: HP Pages: 155

NetStorage 6000

Brand: HP Pages: 192

ProLiant DL100 G2 DPSS

Brand: HP Pages: 44

Brand: Sony Pages: 1

Brand: Sony Pages: 4

Brand: Sony Pages: 64

Brand: Sony Pages: 76

Huge Media Vault - Dual Max

Brand: Huge Systems Pages: 26

Brand: XtendLan Pages: 14

Brand: Sanborn Mfg Pages: 12

Brand: ASUSTOR Pages: 16

Brand: Fantom Drives Pages: 10

Brand: Fantom Drives Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands