IBM System x3690 X5 Service Manual Download | Manualshive

Page: 35 / 464

background image

Server power features

When the server is connected to an ac power source but is not turned on, the
operating system does not run, and all core logic except for the service processor
(the integrated management module) is shutdown; however, the server can
respond to requests from the service processor, such as a remote request to turn on
the server. The power-on LED flashes to indicate that the server is connected to ac
power but is not turned on.

Turning on the server

Approximately 5 seconds after the server is connected to ac power, one or more
fans might start running to provide cooling while the server is connected to power
and the power-on button LED will blink quickly. Approximately 1 to 3 minutes
after the server is connected to ac power, the power-control button becomes active
(the power-on LED will blink slowly), and one or more fans might start running to
provide cooling while the server is connected to power. You can turn on the server
by pressing the power-control button.

The server can also be turned on in any of the following ways:

v

If a power failure occurs while the server is turned on, the server will restart
automatically when power is restored.

v

If your operating system supports the Wake on LAN feature, the Wake on LAN
feature can turn on the server.

Note:

When 4 GB or more of memory (physical or logical) is installed, some

memory is reserved for various system resources and is unavailable to the
operating system. The amount of memory that is reserved for system resources
depends on the operating system, the configuration of the server, and the
configured PCI options.

Turning off the server

When you turn off the server and leave it connected to ac power, the server can
respond to requests from the service processor, such as a remote request to turn on
the server. While the server remains connected to ac power, one or more fans
might continue to run. To remove all power from the server, you must disconnect
it from the power source.

Some operating systems require an orderly shutdown before you turn off the
server. See your operating-system documentation for information about shutting
down the operating system.

Statement 5

CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current from
the device, ensure that all power cords are disconnected from the power source.

Chapter 2. Introduction

17

«
...
33
34
35
36
37
...
»

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

Brand: Hamlet Pages: 10

Brand: Sans Digital Pages: 2

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: AIC Pages: 88

Supporter AM 1200 FH

Brand: Beck Pages: 32

Pietas FlashPen

Brand: Hama Pages: 8

Brand: IBM Pages: 36

PREMIER GAMT41HWJG

Brand: Gladiator Pages: 24

Brand: U-Line Pages: 3

Brand: DFI Pages: 28

Brand: AEG Pages: 16

Brand: Canon Pages: 76

Brand: Dancover Pages: 30

IBM Half-high LTO Generation 3

Brand: Lenovo Pages: 13

Brand: Lenovo Pages: 37

Brand: Lenovo Pages: 46

Brand: Lenovo Pages: 20

IBM Storwize V7000

Brand: Lenovo Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands