manualshive.com logo in svg

IBM System x3690 X5, Service Manual

The IBM System x3690 X5 is a powerful server designed for high performance computing. Ensure efficient use of its features with the At-A-Glance Reference Manual, available for free download on 88.208.23.73:8080. This comprehensive manual will assist you in maximizing the potential of your server for optimal results.

Share
Download
background image

7.

Reinstall the DIMM air baffle, if one was removed (see “Replacing the DIMM
air baffle” on page 271).

8.

Reconnect any cables that your disconnected from the adapters or system
board.

Thermal grease:

The thermal grease must be replaced whenever the heat sink has been removed
from the top of the microprocessor and is going to be reused or when debris is
found in the grease.

When you are installing the heat sink on the same microprocessor that is was
removed from, make sure that the following requirements are met:

v

The thermal grease on the heat sink and microprocessor is not contaminated.

v

Additional thermal grease is not added to the existing thermal grease on the
heat sink and microprocessor.

Note:

v

Read the Safety information on page “Safety” on page vii.

v

Read the “Installation guidelines” on page 261.

v

Read “Handling static-sensitive devices” on page 263.

To replace damaged or contaminated thermal grease on the microprocessor and
heat sink, complete the following steps:

1.

Place the heat sink on a clean work surface.

2.

Remove the cleaning pad from its package and unfold it completely.

3.

Use the cleaning pad to wipe the thermal grease from the bottom of the heat
sink.

Note:

Make sure that all of the thermal grease is removed.

4.

Use a clean area of the cleaning pad to wipe the thermal grease from the
microprocessor; then, dispose of the cleaning pad after all of the thermal grease
is removed.

Microprocessor

0.02 mL of thermal

grease

5.

Use the thermal-grease syringe to place 9 uniformly spaced dots of 0.02 mL
each on the top of the microprocessor. The outermost dots must be within
approximately 5 mm of the edge of the microprocessor; this is to ensure
uniform distribution of the grease.

356

System x3690 X5 Types 7147, 7148, 7149, and 7192: Problem Determination and Service Guide

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

SanDisk Mobile Ultra Memory Stick Micro User Manual preview
Mobile Ultra Memory Stick Micro
Brand: SanDisk Pages: 1
eazished EZ-16242 Assembly Instructions Manual preview
EZ-16242
Brand: eazished Pages: 12
Dancover MS117000 Manual preview
MS117000
Brand: Dancover Pages: 36
MCE Technologies Xcaret Pro-99 Installation Manual preview
Xcaret Pro-99
Brand: MCE Technologies Pages: 9
GARANT GridLine 930505 Instruction Manual preview
GridLine 930505
Brand: GARANT Pages: 116
SanDisk 2GB - 2GB Micro Secure Digital Card Product Manual preview
2GB - 2GB Micro Secure Digital Card
Brand: SanDisk Pages: 26
ABSCO SHEDS 23151SK-PTX Manual preview
23151SK-PTX
Brand: ABSCO SHEDS Pages: 19
ABB MC502 Installation Instructions preview
MC502
Brand: ABB Pages: 2
Fujitsu HandyDrive-5 Operation Manual preview
HandyDrive-5
Brand: Fujitsu Pages: 17
Fujitsu LTO-5 User Manual preview
LTO-5
Brand: Fujitsu Pages: 34
Fujitsu MAS3367FC Product/Maintenance Manual preview
MAS3367FC
Brand: Fujitsu Pages: 114
Fujitsu MAU3036NC Product/Maintenance Manual preview
MAU3036NC
Brand: Fujitsu Pages: 130
Fujitsu GRANPOWER500 TEAMSERVER Series User Manual preview
GRANPOWER500 TEAMSERVER Series
Brand: Fujitsu Pages: 14
Fujitsu MAA3182 Product Manual preview
MAA3182
Brand: Fujitsu Pages: 142
Fujitsu MAN3367FC - Enterprise 36.7 GB Hard Drive Product/Maintenance Manual preview
MAN3367FC - Enterprise 36.7 GB Hard Drive
Brand: Fujitsu Pages: 148
Fujitsu HARD DISK DRIVES MAW3073FC Product/Maintenance Manual preview
HARD DISK DRIVES MAW3073FC
Brand: Fujitsu Pages: 112
Fujitsu LTO-6 User Manual preview
LTO-6
Brand: Fujitsu Pages: 52
Fujitsu IRF-1D series User Manual preview
IRF-1D series
Brand: Fujitsu Pages: 182

Brands by name

Popular brands

Load more brands