IBM System x3690 X5 Service Manual Download | Manualshive

Page: 11 / 464

background image

Inspecting for unsafe conditions

Use the information in this section to help you identify potential unsafe conditions
in an IBM product that you are working on. Each IBM product, as it was designed
and manufactured, has required safety items to protect users and service
technicians from injury. The information in this section addresses only those items.
Use good judgment to identify potential unsafe conditions that might be caused by
non-IBM alterations or attachment of non-IBM features or options that are not
addressed in this section. If you identify an unsafe condition, you must determine
how serious the hazard is and whether you must correct the problem before you
work on the product.

Consider the following conditions and the safety hazards that they present:

v

Electrical hazards, especially primary power. Primary voltage on the frame can
cause serious or fatal electrical shock.

v

Explosive hazards, such as a damaged CRT face or a bulging capacitor.

v

Mechanical hazards, such as loose or missing hardware.

To inspect the product for potential unsafe conditions, complete the following
steps:

1.

Make sure that the power is off and the power cord is disconnected.

2.

Make sure that the exterior cover is not damaged, loose, or broken, and observe
any sharp edges.

3.

Check the power cord:

v

Make sure that the third-wire ground connector is in good condition. Use a
meter to measure third-wire ground continuity for 0.1 ohm or less between
the external ground pin and the frame ground.

v

Make sure that the power cord is the correct type, as specified in “Power
cords” on page 258.

v

Make sure that the insulation is not frayed or worn.

4.

Remove the top cover.

5.

Check for any obvious non-IBM alterations. Use good judgment as to the safety
of any non-IBM alterations.

6.

Check inside the server for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquid, or signs of fire or smoke damage.

7.

Check for worn, frayed, or pinched cables.

8.

Make sure that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.

Safety

ix

«
...
9
10
11
12
13
...
»

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

Brand: IBM Pages: 8

Brand: XenData Pages: 12

Brand: LaCie Pages: 22

StorageLoader DLT VS160

Brand: Tandberg Data Pages: 13

StorageLoader DLT VS160

Brand: Tandberg Data Pages: 46

StorageLibrary LTO-3 SCSI

Brand: Tandberg Data Pages: 2

SDLT220-320 INTEGRATION

Brand: Tandberg Data Pages: 142

Brand: Tandberg Data Pages: 3

Brand: Tandberg Data Pages: 12

Recessed Mounted Pan Door Medicine Cabinets 935/936

Brand: NuTone Pages: 1

TeraStation WSS WS5020N6

Brand: Buffalo Pages: 115

LaCie Ethernet Big Disk

Brand: LaCie Pages: 47

Brand: Qualstar Pages: 205

5BIG THUNDERBOLT 2

Brand: LaCie Pages: 20

Brand: Home Decorators Collection Pages: 5

Brand: Rocstor Pages: 59

Brand: Broadcom Pages: 24

Brand: Nexsan Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands