manualshive.com logo in svg

IBM System x3690 X5, Service Manual

The IBM System x3690 X5 is a powerful server designed for high performance computing. Ensure efficient use of its features with the At-A-Glance Reference Manual, available for free download on 88.208.23.73:8080. This comprehensive manual will assist you in maximizing the potential of your server for optimal results.

Share
Download
background image

Chapter 5. Removing and replacing components

Replaceable components are of three types:

v

Tier 1 customer replaceable unit (CRU):

Replacement of Tier 1 CRUs is your

responsibility. If IBM installs a Tier 1 CRU at your request, you will be charged
for the installation.

v

Tier 2 customer replaceable unit:

You may install a Tier 2 CRU yourself or

request IBM to install it, at no additional charge, under the type of warranty
service that is designated for your server.

v

Field replaceable unit (FRU):

FRUs must be installed only by Trained service

technicians.

See Chapter 4, “Parts listing, System x3690 X5 Types 7147, 7148, 7149, and 7192,”
on page 249 to determine whether a component is a Tier 1 CRU, Tier 2 CRU, or
FRU.

For information about the terms of the warranty and getting service and assistance,
see the

Warranty Information

document that comes with the server.

Installation guidelines

Attention:

Static electricity that is released to internal server components when

the server is powered-on might cause the system to halt, which might result in the
loss of data. To avoid this potential problem, always use an electrostatic-discharge
wrist strap or other grounding system when removing or installing a hot-swap
devices.

Before you remove or replace a component, read the following information:

v

Read the safety information that begins on page “Safety” on page vii and the
guidelines in “Handling static-sensitive devices” on page 263. This information
will help you work safely.

v

Make sure that the devices that you are installing are supported. For a list of
supported optional devices for the server (or MAX5, if one is connected to the
server), see http://www.ibm.com/systems/info/x86servers/serverproven/
compat/us/.

v

When you install your new server, take the opportunity to download and apply
the most recent firmware updates. This step will help to ensure that any known
issues are addressed and that your server is ready to function at maximum
levels of performance. To download firmware updates for your server, go to
http://www.ibm.com/support/fixcentral/.

Important:

Some cluster solutions require specific code levels or coordinated code

updates. If the device is part of a cluster solution, verify that the latest level of
code is supported for the cluster solution before you update the code. For
additional information about tools for updating, managing, and deploying
firmware, see the ToolsCenter for System x and BladeCenter at
http://publib.boulder.ibm.com/infocenter/toolsctr/v1r0/index.jsp.

v

Before you install optional devices, make sure that the server is working
correctly. Start the server, and make sure that the operating system starts, if an
operating system is installed, or that a 19990305 error code is displayed,
indicating that an operating system was not found but the server is otherwise
working correctly. If the server is not working correctly, see Chapter 1, “Start

© Copyright IBM Corp. 2013

261

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

IBM DJNA-351010 Quick Installation Manual preview
DJNA-351010
Brand: IBM Pages: 2
PEAKnx PNX11-10010 Getting Started preview
PNX11-10010
Brand: PEAKnx Pages: 14
Qsan XEVO Manual preview
XEVO
Brand: Qsan Pages: 28
LaCie 301542U Quick Install Manual preview
301542U
Brand: LaCie Pages: 22
Olixir 3DX 120GB Specifications preview
3DX 120GB
Brand: Olixir Pages: 2
Excalibur Do It Yourself Workbench EI-PT1013 User Manual preview
Do It Yourself Workbench EI-PT1013
Brand: Excalibur Pages: 2
Copernicus Tech Tub2 FTT600 Assembly Manual preview
Tech Tub2 FTT600
Brand: Copernicus Pages: 13
TrueNAS M Series Setup Manual preview
M Series
Brand: TrueNAS Pages: 16
D-Link MediaLounge DSM-602H Quick Installation Manual preview
MediaLounge DSM-602H
Brand: D-Link Pages: 12
D-Link SharePort DNS-323 User Manual preview
SharePort DNS-323
Brand: D-Link Pages: 17
D-Link Storage User Manual preview
Storage
Brand: D-Link Pages: 46
D-Link MediaLounge DSM-622H Quick Installation Manual preview
MediaLounge DSM-622H
Brand: D-Link Pages: 16
D-Link MediaLounge DSM-622H User Manual preview
MediaLounge DSM-622H
Brand: D-Link Pages: 46
D-Link MediaLounge DSM-602H User Manual preview
MediaLounge DSM-602H
Brand: D-Link Pages: 39
D-Link ShareCenter 2Go - DNS-213 User Manual preview
ShareCenter 2Go - DNS-213
Brand: D-Link Pages: 87
HP Dv4 1140go - Pavilion Entertainment - Core 2 Duo GHz User Manual preview
Dv4 1140go - Pavilion Entertainment - Core 2 Duo GHz
Brand: HP Pages: 40
HP HDD Troubleshooting Manual preview
HDD
Brand: HP Pages: 48
HP E8D48AA Specifications preview
E8D48AA
Brand: HP Pages: 11

Brands by name

Popular brands

Load more brands