manualshive.com logo in svg

IBM System x3690 X5, Service Manual

The IBM System x3690 X5 is a powerful server designed for high performance computing. Ensure efficient use of its features with the At-A-Glance Reference Manual, available for free download on 88.208.23.73:8080. This comprehensive manual will assist you in maximizing the potential of your server for optimal results.

Share
Download
background image

Removing an IBM ServeRAID B5015 SSD Controller

To remove an IBM ServeRAID B5015 Solid State Drive (SSD) controller, complete
the following steps:

1.

Read the safety information and installation guidelines, see “Safety” on page vii
and “Installation guidelines” on page 261.

2.

Turn off the server (see “Turning off the server” on page 17) and all attached
peripheral devices. Disconnect all power cords; then, disconnect all external
cables as necessary to replace the device.

3.

Remove the top cover (see “Removing the server top cover” on page 264).

4.

Disconnect the cables from the existing SSD adapter.

5.

Carefully grasp the riser card by the blue touch points and pull it up until the
riser-card assembly disengages from the connector on the system board and set
it aside.

6.

Carefully grasp the SSD adapter and pull it out of the riser-card assembly.

7.

If you are instructed to return the adapter, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing an IBM ServeRAID B5015 SSD Controller

Note:

1.

This adapter can only be installed in the PCI slots listed in Table 15 on page
276.

2.

This adapter can only be used with the 8x1.8-inch drive backplane.

3.

You can only use 1.8-inch hot-swap drives with this adapter.

The IBM ServeRAID B5015 Solid State Drive (SSD) controller supports RAID levels
1 and 5. For configuration information, see the ServeRAID documentation at
http://www.ibm.com/systems/support/.

Attention:

Some cluster solutions require specific code levels or coordinated code

updates. If the device is part of a cluster solution, verify that the latest level of
code is supported for the cluster solution before you update the code.

To install an IBM ServeRAID B5015 SSD adapter, complete the following steps:

1.

Read the safety information that begins on page “Safety” on page vii and
“Installation guidelines” on page 261.

2.

Touch the static-protective package that contains the new ServeRAID B5015
SSD adapter to any unpainted surface on the outside of the server; then, grasp
the adapter by the top edge or upper corners of the adapter and remove it
from the package.

3.

Align the ServeRAID B5015 SSD adapter so that the keys align correctly with
the connector on the riser-card assembly.

4.

Insert the SSD adapter into the connector on the riser-card until it is firmly
seated.

Attention:

Incomplete insertion might cause damage to the server or the

adapter.

5.

Reinstall the riser-card assembly onto the system board.

6.

Connect the signal cable to the adapter. Be sure to route the signal cables
through the SAS cable guide and up and over the rear of the microprocessor
air baffle; then, through the loops on the scalability connector cover and then
to the adapter (see the following illustration). Use the cable ties (as shown in
the illustration) that come with the drive backplane to secure the SAS cables

Chapter 5. Removing and replacing components

309

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

Quest Engineering DR4300 Getting Started preview
DR4300
Brand: Quest Engineering Pages: 64
Facilis 8 Hardware Manual preview
8
Brand: Facilis Pages: 28
NEC S2500 User Manual preview
S2500
Brand: NEC Pages: 106
Cutech 80100-CT Manual preview
80100-CT
Brand: Cutech Pages: 2
Microsoft Azure StorSimple 8100 Hardware Installation Manual preview
Azure StorSimple 8100
Brand: Microsoft Pages: 12
Asgard GLADIATOR PLUS 2 Quick Start Manual preview
GLADIATOR PLUS 2
Brand: Asgard Pages: 6
kincrome K7795 Operation Manual preview
K7795
Brand: kincrome Pages: 3
ManoMano 03POH1010-V2 Instructions Manual preview
03POH1010-V2
Brand: ManoMano Pages: 8
QNAP TS-464U User Manual preview
TS-464U
Brand: QNAP Pages: 69
Apricorn Aegis Bio 3.0 Quick Start Manual preview
Aegis Bio 3.0
Brand: Apricorn Pages: 4
Denios HazMat station EPO-2 Operation Manual And Spare Parts List preview
HazMat station EPO-2
Brand: Denios Pages: 6
Eminent EM4172 (Dutch) User Manual preview
EM4172
Brand: Eminent Pages: 112
Rocstor ROCPRO 225 User Manual preview
ROCPRO 225
Brand: Rocstor Pages: 45
kincrome K7308 Operation Manual preview
K7308
Brand: kincrome Pages: 3
HOLZMANN MASCHINEN WB160L Assembly Instruction Manual preview
WB160L
Brand: HOLZMANN MASCHINEN Pages: 18
Seagate ST8000NE0001 Product Manual preview
ST8000NE0001
Brand: Seagate Pages: 32
SanDisk SecureAccess SDCZ73-064G-I35 Quick Start Manual preview
SecureAccess SDCZ73-064G-I35
Brand: SanDisk Pages: 3
SanDisk RS-MMC Brochure preview
RS-MMC
Brand: SanDisk Pages: 2

Brands by name

Popular brands

Load more brands