manualshive.com logo in svg

IBM System x3690 X5, Service Manual

The IBM System x3690 X5 is a powerful server designed for high performance computing. Ensure efficient use of its features with the At-A-Glance Reference Manual, available for free download on 88.208.23.73:8080. This comprehensive manual will assist you in maximizing the potential of your server for optimal results.

Share
Download
background image

Removing the IBM 4x4 Drive Backplane ServeRAID Expansion
adapter

To remove 4x4 Drive Backplane ServeRAID Expansion adapter, complete the
following steps:

1.

Read the safety information and installation guidelines, see “Safety” on page vii
and “Installation guidelines” on page 261.

2.

Turn off the server (see “Turning off the server” on page 17) and all attached
peripheral devices. Disconnect all power cords; then, disconnect all external
cables as necessary to replace the device.

3.

Remove the top cover (see “Removing the server top cover” on page 264).

4.

Disconnect the cables from the existing ServeRAID Expansion adapter.

5.

Carefully grasp the riser card by the blue touch points and pull it up until the
riser-card assembly disengages from the connector on the system board and set
t aside.

6.

Carefully grasp the ServeRAID Expansion adapter and pull it out of the
riser-card assembly.

7.

If you are instructed to return the adapter, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing the IBM 4x4 Drive Backplane ServeRAID Expansion
adapter

The IBM 4x4 Drive Backplane ServeRAID Expansion Adapter provides additional
SAS signal connectors.

Note:

1.

You can only use this adapter with the ServeRAID M1015 SAS/SATA adapter
and the ServeRAID M5015 SAS/SATA adapter. This adapter must be installed
in PCI slot 1 and the ServeRAID M1015 or ServeRAID M5015 adapter
(whichever is installed) must be installed in PCI slot 2 on the two-slot PCI riser
card (see Table 15 on page 276 for more information).

2.

You can only use the 2.5-inch hot-swap drive backplanes with this adapter.

To install an IBM 4x4 Drive Backplane ServeRAID Expansion adapter, complete the
following steps:

1.

Read the safety information that begins on page “Safety” on page vii and
“Installation guidelines” on page 261.

2.

Touch the static-protective package that contains the ServeRAID Expansion
adapter to any unpainted surface on the outside of the server; then, grasp the
adapter by the top edge or upper corners of the adapter and remove it from
the package.

3.

Align the ServeRAID Expansion adapter so that the keys align correctly with
the connector on the riser-card assembly.

4.

Insert the adapter into the connector on the riser-card until it is firmly seated.

Attention:

Incomplete insertion might cause damage to the server or the

adapter.

5.

Reinstall the riser-card assembly onto the system board.

6.

Connect the signal cable to the adapter. Be sure to route the signal cables
through the SAS cable guide and up and over the rear of the microprocessor
air baffle; then, through the loops on the scalability connector cover and then
to the adapter (see the following illustration). Use the cable ties (as shown in
the illustration) that come with the drive backplane to secure the SAS cables

Chapter 5. Removing and replacing components

311

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

D-Link ShareCenter DNS-343 Quick Install Manual preview
ShareCenter DNS-343
Brand: D-Link Pages: 12
i3 International SAN iS316 User Manual preview
SAN iS316
Brand: i3 International Pages: 89
BOH Enviromental BOH-CARGO-12-3 Operator & Maintenance Instructions preview
BOH-CARGO-12-3
Brand: BOH Enviromental Pages: 20
Macpower & Tytech M9 - NDAS User Manual preview
M9 - NDAS
Brand: Macpower & Tytech Pages: 21
Hama Paletto 00108043 Operating Instruction preview
Paletto 00108043
Brand: Hama Pages: 4
DEC DS-HSZ22-AA User Manual preview
DS-HSZ22-AA
Brand: DEC Pages: 94
Mercia Garden Products 03BUT0606-V1 General Instructions Manual preview
03BUT0606-V1
Brand: Mercia Garden Products Pages: 9
Conner CFP4207 Series Product Manual preview
CFP4207 Series
Brand: Conner Pages: 81
Argus SD-0512 Specification Sheet preview
SD-0512
Brand: Argus Pages: 1
Kvaser Memorator Pro 5xHS User Manual preview
Memorator Pro 5xHS
Brand: Kvaser Pages: 27
Hitachi HTS723212L9A360 Specifications preview
HTS723212L9A360
Brand: Hitachi Pages: 176
Hitachi HTS723212L9A360 Install Manual preview
HTS723212L9A360
Brand: Hitachi Pages: 5
Hoshizaki B-300SB Parts List preview
B-300SB
Brand: Hoshizaki Pages: 8
Hoshizaki B-300SF Parts List preview
B-300SF
Brand: Hoshizaki Pages: 15
J.Burrows JBIR41410B Assembly Instructions Manual preview
JBIR41410B
Brand: J.Burrows Pages: 13
Black Box QCE12U User Manual preview
QCE12U
Brand: Black Box Pages: 20
Black Box NBC20S User Manual preview
NBC20S
Brand: Black Box Pages: 24
Fantec DB-228U3 User Manual preview
DB-228U3
Brand: Fantec Pages: 13

Brands by name

Popular brands

Load more brands