IBM System x3690 X5 Service Manual Download | Manualshive

Page: 421 / 464

background image

Setup utility menu choices

The following choices are on the Setup utility main menu for the UEFI. Depending
on the version of the IBM System x Server Firmware (server firmware), some menu
choices might differ slightly from these descriptions.

v

System Information

Select this choice to view information about the server. When you make changes
through other choices in the Setup utility, some of those changes are reflected in
the system information; you cannot change settings directly in the system
information. This choice is on the full Setup utility menu only.
–

System Summary

Select this choice to view configuration information, including the ID, speed,
and cache size of the microprocessors, machine type and model of the server,
the serial number, the system UUID, and the amount of installed memory.
When you make configuration changes through other options in the Setup
utility, the changes are reflected in the system summary; you cannot change
settings directly in the system summary.

–

Product Data

Select this choice to view the system-board identifier, the revision level or
issue date of the firmware, the integrated management module and
diagnostics code, and the version and date.

This choice is on the full Setup utility menu only.

v

System Settings

Select this choice to view or change the server component settings.
–

Adapters and UEFI Drivers

Select this choice to view information about the UEFI 1.10 and UEFI 2.0
compliant adapters and device drivers installed in the server.

–

Network Configuration

Select this choice if you want to use the driver's own configuration capability
to configure the device.

–

Processors

Select this choice to view or change the processor settings.

–

Memory

Select this choice to view or change the memory settings. To configure
memory mirroring, select

System Settings

→

Memory

→

Memory Mirroring

Mode

→

Mirrored

.

–

Devices and I/O Ports

Select this choice to view or change assignments for devices and
input/output (I/O) ports. You can configure the serial ports, configure remote
console redirection, enable or disable integrated Ethernet controllers, the
SAS/SATA controller, SATA optical drive channels, PCI slots, and view the
system Ethernet MAC addresses. If you disable a device, it cannot be
configured, and the operating system will not be able to detect it (this is
equivalent to disconnecting the device).

–

Power

Select this choice to view or change power capping to control consumption,
processors, and performance states.
-

Active Energy Manager

Select this choice to enable or disable power capping. If you enable power
capping, the Active Energy Manager program will limit the maximum
power that is consumed by the server.

Chapter 6. Configuration information and instructions

403

«
...
419
420
421
422
423
...
»

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

Brand: Quest Engineering Pages: 540

Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD

Brand: OCZ Pages: 2

Brand: Hamlet Pages: 10

Brand: BOH Enviromental Pages: 20

Brand: GARANT Pages: 40

Brand: CASARIA Pages: 13

Forensic ComboDock FCDv6

Brand: WiebeTech Pages: 20

Brand: Overland Storage Pages: 4

Brand: Galvo Shed Pages: 2

Brand: LaCie Pages: 2

Brand: Sabio Pages: 2

DataPort 25 Enhanced Carrier

Brand: CRU Dataport Pages: 2

Brand: P.Lindberg Pages: 22

Ultrastar 15K73

Brand: Hitachi Pages: 273

Travelstar 5K500

Brand: Hitachi Pages: 5

Travelstar 5K500.B

Brand: Hitachi Pages: 5

Travelstar 40GN

Brand: Hitachi Pages: 2

Travelstar 4K40

Brand: Hitachi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands