IBM System x3690 X5 Service Manual Download | Manualshive

Page: 427 / 464

background image

Administrator password:

If an administrator password is set, you must type the administrator password for
access to the full Setup utility menu. You can use any combination of 6 to 20
printable ASCII characters for the password.

Attention:

If you set an administrator password and then forget it, there is no

way to change, override, or remove it. You must replace the system board.

Using the Boot Manager program

The Boot Manager program is a built-in, menu-driven configuration utility
program that you can use to temporarily redefine the first startup device without
changing settings in the Setup utility.

To use the Boot Manager program, complete the following steps:

1.

Turn off the server.

2.

Restart the server.

3.

When the prompt

<F12> Select Boot Device

is displayed, press F12. If a

bootable USB mass storage device is installed, a submenu item (

USB Key/Disk

)

is displayed.

4.

Use the Up arrow and Down arrow keys to select an item from the

Boot

Selection Menu

and press Enter.

The next time the server starts, it returns to the startup sequence that is set in the
Setup utility.

Starting the backup server firmware

The system board contains a backup copy area for the server firmware. This is a
secondary copy of the server firmware that you update only during the process of
updating the server firmware. If the primary copy of the server firmware becomes
damaged, use this backup copy.

To force the server to start from the backup copy, turn off the server; then, place
the J59 jumper in the backup position (pins 2 and 3).

Use the backup copy of the server firmware until the primary copy is restored.
After the primary copy is restored, turn off the server; then, move the J59 jumper
back to the primary position (pins 1 and 2).

Chapter 6. Configuration information and instructions

409

«
...
425
426
427
428
429
...
»

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

Brand: ECKELMANN Pages: 134

Brand: Backyard Products Pages: 72

Brand: Asgard Pages: 3

Brand: LaCie Pages: 27

Brand: kincrome Pages: 2

Brand: ATI Technologies Pages: 24

Brand: Western Digital Pages: 2

Brand: Spectra Logic Pages: 15

ST9160310AS - Momentus 5400.5 160 GB Hard Drive

Brand: Seagate Pages: 2

G-RAID mini 1TB

Brand: G-Technology Pages: 13

Brand: DFI Pages: 28

Digi Drive Movie

Brand: Teac Pages: 9

Brand: STILLA Pages: 32

Brand: FUM Pages: 5

Brand: Fulterer Pages: 2

Brand: Displays2go Pages: 2

Brand: Clarke Pages: 8

Brand: Verbatim Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands