IBM System x3690 X5 Service Manual Download | Manualshive

Page: 449 / 464

background image

Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse
A.

Documentation format

The publications for this product are in Adobe Portable Document Format (PDF)
and should be compliant with accessibility standards. If you experience difficulties
when you use the PDF files and want to request a web-based format or accessible
PDF document for a publication, direct your mail to the following address:

Information Development
IBM Corporation
205/A015
3039 E. Cornwallis Road
P.O. Box 12195
Research Triangle Park, North Carolina 27709-2195
U.S.A.

In the request, be sure to include the publication part number and title.

When you send information to IBM, you grant IBM a nonexclusive right to use or
distribute the information in any way it believes appropriate without incurring any
obligation to you.

Electronic emission notices

When you attach a monitor to the equipment, you must use the designated
monitor cable and any interference suppression devices that are supplied with the
monitor.

Federal Communications Commission (FCC) statement

Note:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the
interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes
or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
might cause undesired operation.

Notices

431

«
...
447
448
449
450
451
...
»

Summary of Contents for System x3690 X5

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3690 X5

Brand: Dancover Pages: 30

Brand: SanDisk Pages: 2

RX343-S BLK/SLV

Brand: Rosewill Pages: 2

Brand: Accu Pages: 44

Eternus DX80 S2

Brand: Fujitsu Pages: 186

Brand: Fujitsu Pages: 242

Brand: DeWalt Pages: 76

HTS722010K9A300

Brand: Hitachi Pages: 4

Munchen 63379505

Brand: Profiwerk Pages: 8

Brand: Supero Pages: 112

Brand: Sony Pages: 1

Brand: Sony Pages: 4

Brand: Sony Pages: 64

Brand: Sony Pages: 76

Brand: Toshiba Pages: 1

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 1

Brand: Toshiba Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands