configuration information as IP addresses of various
servers from a BOOTP server.
bridge.
A storage area network (SAN) device that
provides physical and transport conversion, such as
fibre channel to small computer system interface (SCSI)
bridge.
bridge group.
A bridge and the collection of devices
connected to it.
broadcast.
The simultaneous transmission of data to
more than one destination.
cathode ray tube (CRT).
A display device in which
controlled electron beams are used to display
alphanumeric or graphical data on an
electroluminescent screen.
client.
A computer system or process that requests a
service of another computer system or process that is
typically referred to as a server. Multiple clients can
share access to a common server.
command.
A statement used to initiate an action or
start a service. A command consists of the command
name abbreviation, and its parameters and flags if
applicable. A command can be issued by typing it on a
command line or selecting it from a menu.
community string.
The name of a community
contained in each Simple Network Management
Protocol (SNMP) message.
concurrent download.
A method of downloading and
installing firmware that does not require the user to stop
I/O to the controllers during the process.
CRC.
See
cyclic redundancy check
.
CRT.
See
cathode ray tube
.
CRU.
See
customer replaceable unit
.
customer replaceable unit (CRU).
An assembly or
part that a customer can replace in its entirety when any
of its components fail. Contrast with
field replaceable
unit (FRU)
.
cyclic redundancy check (CRC).
(1) A redundancy
check in which the check key is generated by a cyclic
algorithm. (2) An error detection technique performed at
both the sending and receiving stations.
dac.
See
disk array controller
.
dar.
See
disk array router
.
DASD.
See
direct access storage device
.
data striping.
See
striping
.
default host group.
A logical collection of discovered
host ports, defined host computers, and defined host
groups in the storage-partition topology that fulfill the
following requirements:
v
Are not involved in specific logical drive-to-LUN
mappings
v
Share access to logical drives with default logical
drive-to-LUN mappings
device type.
Identifier used to place devices in the
physical map, such as the switch, hub, or storage.
DHCP.
See
Dynamic Host Configuration Protocol
.
direct access storage device (DASD).
A device in
which access time is effectively independent of the
location of the data. Information is entered and retrieved
without reference to previously accessed data. (For
example, a disk drive is a DASD, in contrast with a tape
drive, which stores data as a linear sequence.) DASDs
include both fixed and removable storage devices.
direct memory access (DMA).
The transfer of data
between memory and an input/output (I/O) device
without processor intervention.
disk array controller (dac).
A disk array controller
device that represents the two controllers of an array.
See also
disk array router
.
disk array router (dar).
A disk array router that
represents an entire array, including current and
deferred paths to all logical unit numbers (LUNs) (hdisks
on AIX). See also
disk array controller
.
DMA.
See
direct memory access
.
domain.
The most significant byte in the node port
(N_port) identifier for the fibre-channel (FC) device. It is
not used in the fibre channel-small computer system
interface (FC-SCSI) hardware path ID. It is required to
be the same for all SCSI targets logically connected to
an FC adapter.
drive channels.
The DS4200, DS4700, DS4800,
DS5100, and DS5300 subsystems use dual-port drive
channels that, from the physical point of view, are
connected in the same way as two drive loops.
However, from the point of view of the number of drives
and enclosures, they are treated as a single drive loop
instead of two different drive loops. A group of storage
expansion enclosures are connected to the storage
subsystems using a drive channel from each controller.
This pair of drive channels is referred to as a redundant
drive channel pair.
drive loops.
A drive loop consists of one channel from
each controller combined to form one pair of redundant
drive channels or a redundant drive loop. Each drive
loop is associated with two ports. Drive loops are more
commonly referred to as drive channels. See
drive
channels
.
248
IBM System Storage DS5100 and DS5300 Storage Subsystem: Installation, User’s, and Maintenance Guide