background image

Diagnostics-panel LEDs viewed with the cover off:

Table 22. Diagnostics-panel LED descriptions

Index

Name

Meaning

1

CPU

Microprocessor failure. One or both microprocessors
have failed.

2

VRM

Error on VRM or on integrated voltage regulator. The
LED next to the affected VRM will also be on.

3

Memory

Memory failure. One or more memory DIMMs have
failed.

4

PCI BUS

Error on the PCI bus or system board.

5

Power supply 2

Power supply 2 failure.

6

Power supply 1

Power supply 1 failure.

7

Fan

A fan failed or is operating slowly.

8

Remind button

Press this button to temporarily reset the LEDs on the
diagnostics panel.

9

DASD

A hot-swap hard disk drive, backplane, or other part of
SCSI channel A has failed. The amber LED next to the
drive bay with the failing drive will also be on.

10

NMI

A non-maskable interrupt occurred.

11

Service Processor
bus

The system environmental monitor detected an error.

12

Nonredundant

Nonredundant power.

13

Temperature

The operating temperature inside the engine was
exceeded.

CPU

VRM

MEMORY

DASD

NMI

SERVICE
PROCESSOR BUS

FAN

POWER SUPPLY

PCI  BUS

2

1

NONREDUNDANT

TEMPERATURE

REMIND

8

1

2

3

4

5

6

7

9

11

12

10

13

Figure 13. Diagnostics panel LEDs (viewed with the cover off)

130

NAS Gateway 300 User’s Reference

Summary of Contents for TotalStorage NAS 300









































































































































































































Reviews: