Guidelines
By default the appliance will refuse to accept a packet on an interface other than
the one bound to the destination address of the packet. Use the
disable-interface-isolation
command to disable that behavior and allow any
interface on the same subnet to accept the packet.
As a security policy, the interface receiving a network packet must also be
configured with the IP address that is the destination address of the packet.
Enabling this option relaxes that restriction.
Related Commands
relax-interface-isolation
Examples
v
Allows any interface on the same subnet to accept a packet.
# disable-interface-isolation on
#
ecn-disable
Turn on or off ECN-capable TCP sessions.
Syntax
ecn-disable
{
on
|
off
}
Parameters
on
Stops the generation of ECN-capable TCP sessions.
off
(Default) Generates ECN-capable TCP sessions.
Examples
v
Stops the networking system from generating ECN-enabled TCP sessions.
# ecn-disable on
#
icmp-disable
Disables the generation of a specific Internet Control Message Protocol (ICMP)
reply message.
Syntax
icmp-disable
{
addressmask-reply
|
echo-reply
|
info-reply
|
timestamp-reply
}
no icmp-disable
Parameters
addressmask-reply
,
echo-reply
,
info-reply
, and
timestamp-reply
Specifies the target ICMP reply type to disable.
Guidelines
By default, the appliance replies to the corresponding ICMP requests.
Chapter 50. Network Settings configuration mode
491
Summary of Contents for WebSphere XS40
