Installing
a
hot-swap
SAS
or
hot-swap
SATA
hard
disk
drive
Some
hot-swap
SAS
models
support
2.5-inch
or
3.5-inch
hot-swap
SAS
hard
disk
drives.
The
hot-swap
SATA
models
support
3.5-inch
hot-swap
SATA
hard
disk
drives.
Before
you
install
a
hot-swap
hard
disk
drive,
read
the
following
information:
v
Depending
on
your
model,
the
server
supports
the
following
maximum
number
of
hot-swap
drives:
–
Four
3.5-inch
hot-swap
SAS
–
Four
3.5-inch
hot-swap
SATA
–
Four
2.5-inch
hot-swap
SAS
–
Eight
2.5-inch
hot-swap
SAS
v
You
must
install
either
all
SAS
hard
disk
drives
or
all
SATA
hard
disk
drives
in
the
server.
Do
not
install
both
SAS
and
SATA
drives
in
the
server.
v
Install
drives
in
the
following
sequence:
–
For
server
models
that
support
four
hard
disk
drives,
install
the
drives
starting
from
the
top
bay
to
the
bottom
bay
(bay
4,
5,
6,
and
then
7).
–
For
server
models
that
support
eight
hard
disk
drives,
install
the
drives
starting
from
left
to
right
(bay
4,
5,
6,
7,
8,
9,
10,
and
then
11).
v
Inspect
the
drive
tray
for
signs
of
damage.
v
Make
sure
that
the
drive
is
correctly
installed
in
the
tray.
v
You
do
not
have
to
turn
off
the
server
to
install
hot-swap
drives
in
the
hot-swap
drive
bays.
The
server
hot-swap
bays
are
connected
to
a
SAS/SATA
backplane.
This
backplane,
also
known
as
the
hot-swap-drive
backplane,
is
the
printed
circuit
board
behind
these
bays.
Attention:
Static
electricity
that
is
released
to
internal
server
components
when
the
server
is
powered-on
might
cause
the
server
to
stop,
which
might
result
in
the
loss
of
data.
To
avoid
this
potential
problem,
always
use
an
electrostatic-discharge
wrist
strap
or
other
grounding
system
when
you
work
inside
the
server
with
the
power
on.
To
install
a
hot-swap
hard
disk
drive,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
20.
2.
Unlock
the
side
cover
(the
bezel
will
not
disengage
from
the
server
if
the
cover
is
locked).
3.
Remove
the
lower
bezel
(see
“Removing
the
two-piece
bezel”
on
page
25).
4.
Touch
the
static-protective
package
that
contains
the
drive
to
any
unpainted
metal
surface
on
the
server;
then,
remove
the
drive
from
the
package
and
place
it
on
a
static-protective
surface.
5.
Install
the
hard
disk
drive
in
the
hot-swap
bay:
a.
Make
sure
that
the
drive
tray
handle
is
open.
b.
Align
the
drive
assembly
with
the
guide
rails
in
the
bay
as
shown
in
the
following
illustrations
based
on
your
model.
36
System
x3200
M2
Types
4367
and
4368:
User’s
Guide
Summary of Contents for x3200 M2 Type 4367
