ICE COBOTICS i-SYNEGY i20NBTL+, Operator'S & Parts Manual

ICE /

8

OPERATOR MANUAL

FILLING THE SOLUTION TANK

The machine is equipped with a hose fill-port (see 

machine components, item #18) at the rear of 

the machine, and a bucket fill-port (see machine  

components, item #7) located under the recovery 

tank. Before accessing the bucket fill-port make 

sure that the recovery tank is empty.

Fill the solution tank to the "60L" level on the 

solution tank sight gauge. When using the bucket 

fill-port, stop filling when the level reaches the 

bottom edge of the fill-port.

NOTE: 

When filling the solution tank  with a 

bucket, make sure that the bucket is clean. Do not 

use the same bucket for filling and draining the 

machine.

WARNING: Do not put any flammable 

materials into solution tank. this can cause an 

explosion or a fire. Only use recommended 

cleaning chemicals. Contact your janitorial 

supply distributor for recommendations on 

proper chemicals.

WARNING: Do not operate machine 

unless you have read and understand this 

manual.

1. 

Lower squeegee assembly to the floor by 

lowering the squeegee lift lever(see machine 

components, item #33).

2. 

Lower the scrub head to the floor by stepping 

on the scrub head lift pedal(see machine 

components, item #26).

3.  Swiping the ID card (see machine components, 

item #3) to turn on the machine.

4.  Check the battery meter (see Panel 

components, item #2), if the battery is very low, 

there will be a Fault code & message on the 

LED display screen(see Fault code section), 

and the Fault indicator will blink contiunously 

accompany an audible alarm. please DO NOT 

continue to operate the machine and  recharge 

the batteries immediately.

5. 

Check the solution flow indicator (see Panel 

components, item #5), press the solution flow 

control button (see Panel components, item #6, 

7) to a desired flow rate. 

NOTE: Solution will not begin to flow until 

the control handle bail is pulled.

6.  Turn on the vacuum motor switch(see Panel 

components, item #10).

7.  : Pull the control handle bail(see 

machine components, item #2) backwards to 

start scrubbing by moving the machine forward. 

The drive model / :  Pull the 

control handle bail (see machine components, 

item #2) backwards to start scrubbing. The 

machine will automatically propel forward. 

To reverse the drive model, simply push the 

control handle bail forward.The speed can be 

adjusted, Adjust the speed control button (see 

Panel components, item #13, 15) to a desired 

scrubbing speed. 

NOTE: 

45-60 meters (150-200 ft)per minute is 

the recommended scrubbing speed.

8.  When more brush pressure is needed for heavily 

soiled areas simply lift the down pressure 

lever(see machine components, item #25).

9.  To stop scrubbing, release the control handle 

bail, raise the scrub head and the squeegee 

assembly.

WARNING: Fire Or Explosion Hazard. Do 

Not Pick Up Flammable Materials Or Reactive 

Metals.

1.  Go slow on inclines and slippery surfaces. Do 

not operate the machine on inclines that exceed 

5% (3°). 

2.  Do not keep the machine in the same position 

with pad / brush spinning, keep the machine 

moving to prevent damage to floor finish.

3.  If the squeegee assembly leaves streaks on the 

floor, raise the squeegee off the floor and wipe 

the blades down with a damp cloth. Pre-sweep 

the area to prevent leaving streaks on the floor.

4.  Pour a recommended defoamer into the 

recovery tank if excessive foam appears.

WARNING: Do not allow foam to enter 

the float shut-off screen, vacuum motor 

damage will result. Foam will not activate the 

float shut-off screen.

5.  Occasionally check the battery meter(see Panel 

components, item #2). when the bettery is very 

low, stop scrubbing and recharge the batteries.

           WARNING: When battery  is very low, do 

not continue to operate the machine. Battery 

damage may result.

6.  When the solution tank runs empty, raise the 

brush head off the floor. Keep the squeegee 

down and continue to vacuum until all the dirty 

water is picked up.

NOTE: 

See 

TANK DRAINING

 section to learn how 

to drain recovery and solution tanks.

MACHINE OPERATION

WHILE OPERATING MACHINE