background image

GEM0650/0956/1256 A/W 

 

Control System Diagnostics 

 Page 

24 

 

The Control System consists of: 

Control Board 

Water Sensors 

Ice Sensors 

High Pressure Cut Out 

Low Pressure Cut Out 

 

 
If the unit is 

OFF

, check the 

control  board: 

 

 

1.  Is the Power 

OK

 light on?  If not check power to the unit.  If it has power, and the Power 

OK 

light is 

not

 on, 

check the high pressure and low pressure cut outs.  If they are both closed, replace the board.  If the 

POWER OK

 light is 

ON,

 go to the next step. 

 

2.  Is the Water 

OK

 light on?  If it is, go to the next step.  If not, check the water level in the reservoir.  If there is 

water in the reservoir, check that the water sensor is plugged in.  To check the water sensor: 

   a. Unplug the water sensor. 
   b. Pull the water sensor from the reservoir. 

 c. Place one ohmmeter lead on the sensor’s plug and the other on the sensor’s tip.  The meter should     

show nearly zero (0) resistance.  If it reads infinite resistance, check the tip for corrosion.  If it is clean and 
still reads open, replace the sensor.  

      OR, connect a copper wire to the wire where the water sensor plugs into and place the other end in the 

water.  The 

WATER

 

OK 

should go 

ON. 

 If it does not, replace the board. 

 

3. 

 Ice sensor Check

. Is the 

BIN FULL

 light 

OFF

?  If it is 

OFF

 and the 

SERVICE

 light is 

OFF

 and the unit is not 

running, replace the control board.   

  a. If it is 

OFF

 and the auger motor is running but the compressor is not, check the compressor contactor coil. 

  b. If it is 

ON

, the ice sensors may be blocked.  Remove them and check for mineral scale.  

 

 

4.

  High pressure 

cut out check. 

 

a

Disconnect electrical power. 

  b. Pull the wires off the high pressure cut out. 

   c. Use an ohmmeter to determine if the switch is 

OPEN

.  If it is, check the discharge pressure.  If the    

discharge pressure is less than 300 PSIG, replace the high pressure cut out.  

  d. If the high pressure cut out is open and the system has high discharge pressure, check for the cause. 
   
5.

  Low pressure 

cut out check. 

 

a.

 

Disconnect electrical power. 

  b. Pull the wires off the low pressure cut out. 

   c. Use an ohmmeter to determine if the switch is 

OPEN

.  If it is, check the suction pressure.  If the suction  

pressure is greater than 20 PSIG, replace the low pressure cut out.  

  d. If the low pressure cut out is open and the system has low suction pressure, check for the cause. 
 

Summary of Contents for GEM0650A/W












































Reviews: