background image

July 2013

Page 9

User Manual for Models HISU056, HISU076 AND HISU096

Ice Bridge Thickness Adjustment Area

Master Switch. Move to ON (left side depressed) to make ice, OFF 

(centered) to shut off and WASH (right side depressed) for use in 

cleaning.

Harvest Time Adjustment Area

Indicator Light Area. 

Freeze mode light is ON when unit is in a Freeze cycle. 

Timer On light is ON when trigger point temperature is reached in 

Freeze or Harvest.

Harvest Cycle Time Adjustment

After ice has formed in the inverted mold, it must be 

released so it can be deposited in the storage bin 

section. The harvest cycle is when that occurs, and 

must be long enough for the ice to release. While the 

harvest cycle length is self adjusting it can also be 

manually adjusted if needed. 

Proper harvest time is when the ice falls into the 

bin and there is about 10 seconds extra harvest 

time (pump and fan are off) before the freeze cycle 

restarts.

If the harvest time is too short to release the ice, 

the time may be increased by pushing the + sign on 

the harvest time adjustment section of the control 

panel. Operate the machine for another cycle to 

confirm that the adjustment was correct. Note that too 

much harvest time will slightly decrease making ice 

capacity.

Control Panel and Adjustments

Adjustment Indicator Lights 

Each push and release of the + or - button will change 

the lights that glow or blink indicating a change in ice 

size or harvest time. Example: p one time 

changes a blinking light to steady on type. If the lights 

are on steady a single push of + will add one more 

light to the right and it will blink. There are 10 settings. 

All 5 lights on steady is the maximum setting and one 

blinking light is the minimum.

Ice Too Thin

Ice Too Thick

Ice Just Right

Bridge

Ice Thickness Diagram

Ice Bridge Thickness Adjustment

Refer to the Ice Thickness Diagram for proper ice 

size.

Adjust by pushing the + sign or – sign on the ice 

bridge adjustment section of the control panel. 

Changing bridge thickness should be a one-time 

adjustment as the machine will automatically maintain 

that ice thickness. 

-

+

-

+

Ice Bridge Thickness Adjustment

Ajuste da espessura da ponte de gelo

Harvest Time Adjustment

Ajuste do tempo de colheita

ON   /   OFF  /   WASH

Ligar / desligar / lavar

Freeze Mode

Modo de congelamento 

Timer On

Temporizador ligado

17-3386-41

Summary of Contents for HISU056


















Reviews: